To USE the Depth Control Lever

•Position your Edger in desired edging lo- cation before operating.

•Start the engine and move the depth control lever back to lower the cutting blade.

•Select the edging depth you need. There are 3 selections up to approxi-

mately 2 inches deep.

IMPORTANT: If very deep edging is required, we recommend that a shallow cut be made first, then cut at greater depths until the desired depth is ob- tained.

/_ WARNING: Keep away from the rotat- ing blade. The blade can cause injury.

TO USE THE INDEX LEVER (BEVELING OPERATION)

•Stop engine and disconnect the spark plug wire from the spark plug.

INDEX LEVER IN THE NOTCH MARKED BEVEL CUT

•Pull the index lever out of the edging

notch as shown above and position it in the notch marked bevel cut.

•Reconnect the spark plug wire and

start the engine. Move the depth control lever to the desired beveling

depth.

_ CAUTION: Never leave the Edger unattended while the engine is running. Prior to adjusting the indexing blade posi- tion, always raise the cutting blade and stop the engine.

WARNING: Keep away from the rotating blade. The blade can cause injury.

TO USE THE BEVEL CUT FEATURE

Bevel edging reduces the need to edge as often creating a type of trench along your

sidewalk, driveway and etc. Move the in- dex lever to the bevel cut position and se- cure index lever in the slot. Prior to starting the engine, line the Edger up as ff you were going to bevel cut and move the depth con- trol lever down to test the blade location. Return the depth control lever to the for- ward slot of the adjustment bracket to raise the blade. Start the engine and move the depth control lever to the desired depth of cut.

BEFORE STARTING ENGINE

PRE-USE CHECK OF CONTROLS

All controls should be checked for proper function before servicing or starting the

engine.

•Move the depth control lever into all

three positions in the selector plate. Make sure the depth control lever snaps

into all three holes as shown in figure on page 6.

•Return the depth control lever to the forward hole in the selector plate.

FILL/ADD OIL:

This Edger was shipped with a 20 ounce container of SAE30 motor oil. This oil must

be added to the engine before operating. Remove the oil fill cap/dipstick and fill the crankcase to FULL line on dipstick. Your

engine may not require the entire 20 ounces of oil. DO NOT OVERFILL.

NOTE: Engine may already contain some residual oil.

Tighten the fill cap/dipstick securely each

time you check the oil level.

OIL RECOMMENDATIONS

Only use high quality detergent oil rated with API service classification SG. Select

the oil'sSAE viscosity grade according to

your expected operating temperature:

<<__Colder(<*W30 --__ 3--_2°F-_A'LL'35>>Warmer>>I

NOTE: Although multi-viscosity oils (5W30, 10W30, etc.) improve starting in cold we_tther, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level

more frequently to avoid possible engine damage from running low on oil.

536.7722 specifications

The Craftsman 536.7722 is a versatile and robust snow blower that has become a favorite among homeowners for its efficiency and reliability in clearing snow during harsh winter months. This model is designed to handle various snow conditions, making it an ideal choice for those living in areas with heavy snowfall.

One of the standout features of the Craftsman 536.7722 is its powerful engine. It is equipped with a reliable 5.5 horsepower engine that provides ample power to tackle even the toughest snow accumulation. The engine is designed for easy start-up, ensuring that users can get to work quickly without the fuss of traditional pull-start mechanisms.

The snow blower features a 22-inch clearing width, allowing it to efficiently clear paths, driveways, and sidewalks in a single pass. This larger width reduces the time and effort needed to clear snow, making it an efficient choice for both small and medium-sized areas. The adjustable chute is another highlight of the Craftsman 536.7722. It allows users to control the direction and distance the snow is thrown, with a rotation capability of up to 190 degrees. This feature enables precise snow removal and prevents the need for repeated passes over the same areas.

The Craftsman 536.7722 is also equipped with an innovative auger system, which enhances its snow-clearing capabilities. The heavy-duty auger is designed to break down and scoop up snow with ease, ensuring that even packed snow can be cleared effectively. The snow blower operates with a two-stage system, which means the auger collects the snow and sends it to an impeller that throws it out of the chute, allowing for efficient snow dispersal.

In addition to its performance features, the Craftsman 536.7722 is built with comfort in mind. The ergonomic handles are designed for ease of use, and they can be adjusted to suit different user heights. The snow blower’s compact design allows for easy maneuverability in tight spaces, making it ideal for residential use.

Overall, the Craftsman 536.7722 combines power, efficiency, and user-friendly features, making it a reliable tool for anyone looking to keep their property clear of snow throughout the winter season. With its robust construction and advanced technology, this snow blower stands out as a top contender in the market for homeowners seeking effective snow removal solutions.