Gardena EN61000-3-11, EN61000-3-2, EN55014-1, EN50366 Maintenance and Storage, Cutting Techniques

Page 17

G. MAINTENANCE AND STORAGE

Before performing any maintenance or cleaning, remove the plug from the mains.

ATTENTION! In cases where work environments are particularly dirty or dusty, the

operations described must be performed more frequently than mentioned in the instructions.

Before each use

Check that the chain oil pump functions correctly: direct the bar towards a clear surface at a distance of about 20 centimetres; after the machine has run for about a minute, the surface should show clear traces of oil (fig.1).

Check that excessive strength is not needed for activating and deactivating the chain brake. Also check that it is not activated too easily and that it is not blocked. Then check chain brake function as follows: release the chain brake, grip the machine correctly and start up the machine, activate the chain brake by pushing the front hand guard forward with the left wrist or arm but without removing the hand from the handle (fig.2). If the chain brake is working correctly, the chain should be stopped immediately.

Check that the chain is sharpened correctly, in good working condition and that the tension is correct. If the chain is irregularly worn, or if the cutting teeth are only 3 mm long, the chain must be replaced (fig.3).

Clean the air vents regularly to prevent motor overheating (fig 4).

Check that the switch and switch block function correctly (to be performed with the chain brake released): press the switch and the switch block and ensure that they return to idle position as soon as they are released; check that it is impossible to press the switch without activating the switch block.

Check that the chain catcher and the right hand guard are in correct condition without any visible faults such as damaged material.

Every 2-3 hours of use

Check the bar condition, if necessary clean the lubrication holes (fig.5) and the guide grooves (fig.6) carefully; If the groove is worn or shows signs of deep notching, it must be replaced. Clean the drive sprocket regularly and check that it has not been subject to excess wear (fig.7). Lubricate the nose sprocket with bearing grease through the hole shown in the illustration (fig.8).

Chain sharpening

Contact an Authorised Service Centre regarding any problems with sharpening the chain.

The chain needs to be correctly sharpened. A wrongly sharpened chain can cause kickback

and a high risk of injury.

If the chain does not cut correctly, or requires hard bar pressure against the wood, and if the sawdust is very fine, this is a sign that it is not sharpened correctly. If the cutting action produces no sawdust, this means the cutting edge has been worn completely and the chain is pulverising the wood during cutting. A well- sharpened chain crosses through the wood without effort or pressure and produces large long wood shavings.

The cutting side of the chain is composed of the cutting link (fig.9) with a cutting tooth (fig.10) and a cutting limit gauge (fig.11). The difference between these determines the cutting depth; a file guide and a 4mm diameter round file are needed to obtain good sharpening results; Follow the instructions below: Once the chain has been mounted and the tension is correctly adjusted, and the chain brake is activated, position the file guide perpendicular to the bar as shown in the illustration (fig.12), filing the cutting teeth at the angle shown (fig.13A & 13B), always working from the interior towards the exterior, lessening the pressure during the return stage (it is very important to follow the instructions perfectly: excessive or insufficient sharpening angles or an incorrect file diameter will increase the risk of kickback.) To obtain higher precision on side angles, it is advisable to position the file so that it exceeds the upper cutter by about 0.5 mm. File all the teeth on one side first, then turn the machine over and repeat the operation. Make sure that after sharpening operations, all teeth are the same length and that the height of the depth gauge is

0.6mm lower than the upper cutter: check the height using a proper template and file (with a flat file) all protruding parts, rounding off the front part of the depth gauge (fig.14), paying attention to not file the kickback protection tooth (fig.15)

Every 30 hours use.

Take the machine to the Authorised Service Centre

Storage/Transport

Allow the product to cool down and place the cover over the bar and chain.

Store the product in a cool, dry, place and out of reach of children. Do not store outdoors.

Ensure the oil does not leak out from the product.

H. CUTTING TECHNIQUES

(fig.1) When using the machine, prevent:

-cutting in conditions where the trunk could split during cutting (wood under pressure, dry dead trees, etc): sudden splitting can be very dangerous.

-the bar or the chain from becoming blocked in the cutting notch: if this should occur, disconnect the machine from the main electricity supply and try to raise the trunk using an appropriate tool as a lever; do not attempt to free the machine by shaking or pulling as this could cause damage or injury.

-situations that can lead to kickback reactions.

-using the product above shoulder height

-cutting wood with foreign objects e.g. nails.

Never use the machine in earth or stones, this leads to immediate wear of the chain.

(fig.1) During machine use:

-When cutting on sloping ground, always work uphill of the trunk to avoid being hit if the trunk should roll downhill.

-When felling trees, always finish the job: a partially cut tree could break and fall.

-At the end of each cutting operation the user will notice a considerable change in the strength necessary for controlling the machine. Great care must be taken not to loose control.

Below is a description of two different types of cutting operation:

Cutting action by pulling the chain (from top to bottom) (fig.2) can lead to dangerous sudden movement of the machine towards the trunk with consequential loss of control. Where possible, use the spiked bumper during cutting operations.

ENGLISH - 7

Image 17
Contents Gardenaæ Wichtige Information Page 143 Page 3mm Page 5mm Page Page English General DescriptionSave all warnings and instructions for future reference Safety PrecautionsGeneral Power Tool Safety Warnings English Causes and operator prevention of kickback Work area safetyCables Safety Equipment DescriptionSTART-UP and Stopping Assembly / DisassemblyBAR and Chain Lubrication Choice of chain oilCutting Techniques Maintenance and StorageTrunk supported at both ends. Risk of pinching the chain Spiked bumper useTree felling Felling CutsEnvironmental Information Troubleshooting Table98/37/EC, 2004/108/EC, 2000/14/EC CST3018, CST35182009 USA

EN60745-1, EN50366, EN60745-2-13, EN61000-3-2, EN55014-1 specifications

Gardena, a prominent name in the gardening tools sector, offers products designed to meet rigorous European standards for electromagnetic compatibility and safety. Among these standards are EN61000-3-11, EN55014-1, EN61000-3-2, EN60745-2-13, and EN50366. Each of these standards ensures that Gardena tools are efficient, safe, and environmentally friendly.

EN61000-3-11 pertains to the limits for voltage fluctuations and flicker in electrical equipment connected to a low-voltage supply system. Gardena tools designed in compliance with this standard minimize their impact on the electrical grid, ensuring reliable operation even in environments with fluctuating power quality. This commitment is evident in their well-engineered motors, which exhibit resilience against voltage fluctuations.

EN55014-1 covers the emission of electromagnetic disturbances from household appliances and similar tools. By adhering to this standard, Gardena products effectively suppress electromagnetic interference, promising a quiet operation and reducing the likelihood of disruption to other electronic devices in the vicinity.

EN61000-3-2 is crucial for harmonic current emissions in devices with input current up to 16 A. Gardena's adherence to this standard shows its commitment to sustainability; the products generate minimal harmonic distortion, which is vital for maintaining grid stability and optimizing energy consumption.

Gardena's tools also conform to EN60745-2-13, focusing on safety requirements for handheld motor-operated tools. This standard ensures that Gardena’s offerings prioritize user safety, featuring ergonomic designs, protective mechanisms, and low-risk operation features. Such safety measures enhance user confidence while offering peace of mind during gardening tasks.

Lastly, EN50366 deals with the basic requirements for the immunity of electrical and electronic appliances aimed at preventing disturbances from electromagnetic radiation. Gardena's compliance with this standard underlines the brand's dedication to user safety and product reliability. The tools are designed to minimize radiation emissions, which conservatively supports both users and the environment.

In essence, Gardena’s alignment with standards such as EN61000-3-11, EN55014-1, EN61000-3-2, EN60745-2-13, and EN50366 highlights the brand's commitment to delivering high-quality gardening products that are efficient, safe, and environmentally responsible. Customers can trust that they are investing in tools designed with cutting-edge technology and compliance to the highest European safety and performance standards.