Orion 3002 manual Step By Step Installation

Page 13

Pliers (standard and needle nose)

Reference CD with 1 kHz Sine Wave at 0dB level (all bits high)

RTA (real time analyzer)

Soldering iron and solder

Utility knife

Wire brush or sandpaper for chassis grounding

Wire crimper

Wire cutters

Wire strippers

Step By Step Installation

Step 1 Determine the location for the amplifier. Refer to the Choosing Mounting Locations section of this guide for detailed information.

Step 2 Decide on the system configuration for your amplifier. For system sugges- tions, refer to the Speaker Connections section of this guide.

Step 3 Run all the wires from the amplifier location to the speakers, source unit, and battery. Do not connect the battery at this time. Be sure to run RCAs and power and speaker wires away from factory electrical wires and system as they pose a great potential for induced system noise.

Step 4 Pre-drill amplifier mounting holes. Be sure to "think before you drill". Gas tanks, fuel lines, and other obstructions have a nasty way of hiding them- selves. For best results use a marking pen to mark the mounting holes and pre-drill these holes with a standard 1/8" drill bit.

Step 5 Mount the amplifier. Make sure the amplifier is mounted on a flat surface. If this is not possible, do not over tighten the screws so that the chassis of the amplifier is twisted or bent.

Step 6 Turn the vehicle's key switch to the off position.

Step 7 Disconnect the vehicle's battery ground terminal.

Step 8 Connect the RCA and speaker wires to the amplifier. Check the quality of your speakers and signal connections. This will determine the ultimate per- formance of your Orion amplifier. Refer to the Signal Input and Output Level Controls and Speaker Connections sections of this manual for correct wiring instructions.

Step 9 Connect power wires to the amplifier. At this time do not connect the fuse at the main battery.

Step 10 Reconnect the ground terminal to the battery.

Step 11 Set crossovers. Refer to the Internal Crossover Configuration section of this manual for detailed instructions.

Step 12 Once satisfied that all connections and settings are correct, install the fuse located near the vehicle's battery and proceed to the Testing the System sec- tion of this manual.

WARNING! Never exceed the recommended fuse size of this amplifier. Failure to do so will result in voiding of your warranty and possible damage to the amplifier.

12

©2004 Directed Electronics, Inc.

Image 13
Contents Page Contents Practice Safe Sound IntroductionWhat’s in the Box Record Your Serial Number and Date Limited TWO-YEAR Consumer WarrantyAmplifier Section Orion SpecificationsAmplifier Controls and Connections Stereo / Mono Input Configuration Amplifier SettingsInternal Crossover Configuration Low-Pass CrossoverInput Gain High-Pass CrossoverINTELLi Bass Control Power Connections Amplifier WiringSpeaker Connections Summed Bridged Configuration Choosing Mounting Locations Amplifier InstallationPassenger Compartment Trunk CompartmentTools of the Trade General Precautions and Installation TipsStep By Step Installation Testing the System SET UP and TroubleshootingAdjusting the Sound of the System Directed Electronics, Inc Symptom Probable Cause Action To Take Troubleshooting TipsInternal Crossover Configuration Directed Electronics, Inc Warranty

3002 specifications

The Orion 3002 is a highly advanced spacecraft designed for deep-space exploration, research, and potential colonization missions. Boasting cutting-edge technologies and innovative engineering, the Orion 3002 is a hallmark of modern aerospace design, focusing on efficiency, reliability, and adaptability.

One of the primary features of the Orion 3002 is its powerful propulsion system, which employs a hybrid of traditional chemical propulsion and advanced ion thrusters. This combination allows for swift maneuverability within the Earth's atmosphere and efficient long-duration travel in the vacuum of space. The ion thrusters utilize electric fields to accelerate ions, providing a thrust that is highly efficient and capable of extending travel durations.

The spacecraft is constructed using lightweight, durable materials that significantly enhance its structural integrity without impeding performance. The exterior is designed to withstand the harsh conditions of space, including fluctuations in temperature, radiation exposure, and micrometeorite impacts. Additionally, the Orion 3002 is equipped with advanced thermal protection systems that maintain optimal operating conditions for onboard systems and crew.

The Orion 3002 features a cutting-edge avionics suite that integrates artificial intelligence and machine learning algorithms. These systems are capable of real-time data analysis, enabling the spacecraft to make autonomous decisions regarding navigation, course adjustments, and systems monitoring. This level of intelligence not only enhances safety but also allows for more complex mission profiles, including those requiring minimal human oversight.

In terms of crew accommodations, the Orion 3002 prioritizes comfort and functionality. The living quarters are designed to support long-duration missions with ergonomic sleeping arrangements, a fully equipped galley, and dedicated research labs that allow astronauts to conduct a variety of experiments during their travels. Advanced life support systems recycle air and water, ensuring sustainability throughout the mission.

The Orion 3002 also incorporates advanced communication systems that enable seamless, high-bandwidth data transmission over vast distances. This technology employs a series of relay satellites and deep-space communication networks, ensuring that the crew remains connected with mission control and can share their findings efficiently.

In conclusion, the Orion 3002 stands as a testament to human ingenuity and the quest for knowledge beyond our planet. With its blend of advanced technologies, durable construction, and crew-centric design, it is well-equipped to tackle the challenges of deep-space missions, paving the way for future exploratory endeavors that expand our understanding of the universe.