Before Starting the Engine, To Start Engine

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. Use the slope guide at the back of this manual.

• Choose the slowest speed before starting

up or down hills.

• Avoid stopping or changing speed on

hills.

• If stopping is absolutely necessary, push

clutch/brake pedal quickly to brake position

•For cold weather operation you should change oil for easier starting (See the oil viscosity chart in the Maintenance section of this manual).

•To change engine oil, see the Mainte- nance section in this manual.

ADD GASOLINE

• Fill fuel tank to bottom of filler neck. Do

not overfill. Use fresh, clean, regular

unleaded gasoline with a minimum of

87 octane. (Use of leaded gasoline will

RIDING MOWER - -CATALOG NO. WE261

SCHEMATIC

SCH21		BATTERY
	FUSE-5A	BATTERY
	FUSE-5A
RED	RED		BLACK
		STARTER
		RELAY	STARTER
			STARTER

and engage parking brake.

• Move motion control lever to neutral (N)

position.

• To restart movement, slowly release park-

ing brake and clutch/brake pedal.

• Make all turns slowly.

TO TRANSPORT

When pushing or towing your riding mower, be sure to disengage transmission by placing

increase carbon and lead oxide deposits

and reduce valve life). Do not mix oil with

gasoline. Purchase fuel in quantities that

can be used within 30 days to assure fuel

freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

B S M

GA1

L A2

RED

FUSE-40A

WHITE

VIOLET

	VIOLET	VIOLET
BLACK/WHITE	CLUTCH / BRAKE	ATTACHMENT CLUTCH
	(PEDAL UP)	(CLUTCH OFF)

		TO IGN. SWITCH ‘A1’
85	86	RED
		RED
30	87	BLACK
30	87
	87A

A B C D E F

SAFETY START MODULE

freewheel control in freewheel position. Freewheel control is located at the rear drawbar of the riding mower.

•Raise mower height adjustment to its highest position with mower height adjustment lever.

•Push freewheel control down and over with foot.

Freewheel

Control

Disengaged

Freewheel

Control

Engaged

•To reengage transmission, reverse above procedure, or press brake lever all the way down.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your riding mower has been shipped, from the factory, already filled with

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

1.	Be sure freewheel control is in the
	transmission engaged position.
2.	Sit on seat in operating position,
	depress clutch/brake pedal and set
	parking brake.
3.	Place motion control lever in neutral
	(N) position.
4.	Move deck clutch to disengaged posi-
	tion.
5.	Insert key into ignition and turn key

BLACK	BLACK/WHITE	BLACK/WHITE
BLACK	RED		SEAT SWITCH
		GREEN	(NOT OCCUPIED)
		GREEN	BLACK
		GRAY	BLACK

	REVERSE SWITCH
	NOT IN REVERSE	SHORTING CONNECTOR
		SHORTING CONNECTOR
YELLOW		BLACK

BLACK/WHITE	IGNITION
	UNIT

SPARK PLUG

GAP

CHARGING SYSTEM OUTPUT	28 VOLTS AC MIN. @ 3600 RPM
. 5 AMP DC @ 3600 RPM	(CHARGING SYSTEM DISCONNECTED)

RED

DIODE

STATOR

SAFETY START MODULE

VIEWED FROM MATING SIDE

summer weight oil.

1.Check engine oil with riding mower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

clockwise to start position and release

key as soon as engine starts. Do not

run starter continuously for more than

fifteen seconds per minute. NOTE: If at high altitude (above 3000 feet) or in cold temperature (below 32°F) the fuel mixture may need to be adjusted for best performance.

IGNITION SWITCH

POSITION	CIRCUIT	“MAKE”

OFF	M+G+A1
RUN/OVERRIDE	B+A1
RUN	B+A1	L+A2
START	B + S + A1

WIRING INSULATED CLIPS

NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE RE-INSTALLED TO PROPERLY SECURE YOUR WIRING.

REMOVABLE CONNECTIONS

NON-REMOVABLE CONNECTIONS

WE261 specifications

The Weed Eater WE261 is a robust and versatile string trimmer designed to tackle a variety of lawn care tasks with ease and efficiency. Aimed at both homeowners and landscaping professionals, the WE261 is built to handle the challenges of overgrown lawns and garden beds, providing powerful performance and reliability.

One of the standout features of the WE261 is its 26cc 2-cycle engine, which delivers ample power while maintaining a lightweight profile. This engine ensures that users can navigate through dense vegetation and thick weeds without compromising performance. The 2-cycle technology allows for efficient fuel usage, providing users with longer run times between refuels.

The WE261 is equipped with a dual line bump head, which automatically releases more line as needed. This feature enhances productivity by allowing the user to focus on trimming rather than manually adjusting the string. The .095-inch line diameter provides a thick cutting path, making it effective against stubborn weeds and tall grass.

Another significant characteristic of the WE261 is its ergonomic design. The trimmer features a padded hand grip and an adjustable handle, allowing users to customize their grip for maximum comfort and control. This is especially beneficial during extended use, as it minimizes fatigue and enhances maneuverability.

The trimmer also incorporates an easy-start technology, which simplifies the starting process. Users can enjoy quick and hassle-free starts with minimal effort required. This feature is particularly useful for those who may not have extensive experience with starting gas-powered equipment.

Durability is a key consideration in the design of the WE261. Constructed with high-quality materials, this weed eater is built to withstand the rigors of regular use. The robust build ensures that it can handle various outdoor conditions, making it a reliable option for any lawn care enthusiast.

In summary, the Weed Eater WE261 presents a combination of power, efficiency, and user-friendly features. With its strong 26cc engine, automatic dual line bump head, ergonomic design, and easy-start technology, it stands out as an exceptional choice for anyone looking to maintain a well-groomed lawn. Whether dealing with overgrown areas or simply keeping the yard tidy, the WE261 is up to the task, delivering performance that users can trust.