Weedeater WE261 Lawn Mower Service & Adjustments

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

1.Depress clutch/brake pedal fully and set parking brake.

2.Place motion control lever in neutral (N) position.

3.Place deck clutch in “DISENGAGED” position.

4.Turn ignition key to “STOP” and remove key.

5.Make sure the blade and all moving parts have completely stopped.

6.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO LEVEL MOWER HOUSING

Adjust the mower while riding mower is parked on level ground or driveway. Make sure tires are properly inflated (See side of tire for proper PSI). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

• Raise mower to its highest position.

• Measure distance "A" from bottom edge

of mower to ground level at front corners

of mower.

• To raise the right side of the mower, tighten

lift link adjustment nut.

• To lower the right side of the mower, loosen

Nut "G"

Nut "H"

Trunnion

RIDING MOWER

TO REMOVE MOWER

1.Place deck clutch in “DISENGAGED" position.

2.Move mower height adjustment lift lever forward to lower mower to its lowest position.

3.Remove mandrel cover.

4.Remove pins holding left and right front mower suspension arms in place.

5.Remove bolt holding deck front to rear leveling rod in place.

6.Remove pin holding deck lift link arm in place.

7.Remove bolt holding deck side to side leveling rod in place.

8.Remove belt from around pulleys.

9.Slide deck out from under side of mower.

TO INSTALL MOWER

Install in reverse order following instructions in "TO REMOVE MOWER" section.

lift link adjustment nut.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

Bottom Edge of	Bottom Edge of
Mower to Ground	Mower to Ground

TO REPLACE MOWER BLADE DRIVE BELT

MOWER DRIVE BELT REMOVAL

1.	Park riding mower on a level surface.
2.	Set parking brake.
3.	Lower mower to its lowest position.

Deck Leveling

Side to Side

Rod Bolt

Mandrel Cover

Front Leveling

Rod Bolt

	Mower	Deck Lift
	Mower	Link Pin
	Suspension	Link Pin
	Suspension
	Arm Pin

•Recheck measurements after adjusting.

FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to side.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of riding mower. Measure distance “F” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•To lower front of mower housing turn nuts “G” and “H” clockwise.

•When distance “F” is 1/8" to 1/2" lower at front than rear, tighten nut “H” against trunnion on front link.

•To raise front of mower housing turn nuts “G” and “H” counter clockwise.

•When distance “F” is 1/8" to 1/2" lower

at front than rear, tighten nut “H” against trunnion on front link.

NOTE: Each full turn of "G" will change "F" by approximately about 3/8".

• Recheck side-to-side adjustment.

4.	Remove mandrel cover from mower
	deck.
5.	Remove rear engine plate from unit.
6.	Remove rear belt keeper from unit.
7.	Carefully roll belt over the top of the
	mower blade mandrel.
8.	Remove belt from idler pulleys.

Mower Drive Belt

Belt

Keeper

Mandrel	Idler Pulleys

9.Check idler pulleys to see that they rotate freely.

10.Remove belt from rear drive pulley.

MOWER DRIVE BELT INSTALLATION Install in reverse order following instruc- tions in "MOWER DRIVE BELT REMOVAL" section.

WE261 specifications

The Weed Eater WE261 is a robust and versatile string trimmer designed to tackle a variety of lawn care tasks with ease and efficiency. Aimed at both homeowners and landscaping professionals, the WE261 is built to handle the challenges of overgrown lawns and garden beds, providing powerful performance and reliability.

One of the standout features of the WE261 is its 26cc 2-cycle engine, which delivers ample power while maintaining a lightweight profile. This engine ensures that users can navigate through dense vegetation and thick weeds without compromising performance. The 2-cycle technology allows for efficient fuel usage, providing users with longer run times between refuels.

The WE261 is equipped with a dual line bump head, which automatically releases more line as needed. This feature enhances productivity by allowing the user to focus on trimming rather than manually adjusting the string. The .095-inch line diameter provides a thick cutting path, making it effective against stubborn weeds and tall grass.

Another significant characteristic of the WE261 is its ergonomic design. The trimmer features a padded hand grip and an adjustable handle, allowing users to customize their grip for maximum comfort and control. This is especially beneficial during extended use, as it minimizes fatigue and enhances maneuverability.

The trimmer also incorporates an easy-start technology, which simplifies the starting process. Users can enjoy quick and hassle-free starts with minimal effort required. This feature is particularly useful for those who may not have extensive experience with starting gas-powered equipment.

Durability is a key consideration in the design of the WE261. Constructed with high-quality materials, this weed eater is built to withstand the rigors of regular use. The robust build ensures that it can handle various outdoor conditions, making it a reliable option for any lawn care enthusiast.

In summary, the Weed Eater WE261 presents a combination of power, efficiency, and user-friendly features. With its strong 26cc engine, automatic dual line bump head, ergonomic design, and easy-start technology, it stands out as an exceptional choice for anyone looking to maintain a well-groomed lawn. Whether dealing with overgrown areas or simply keeping the yard tidy, the WE261 is up to the task, delivering performance that users can trust.