Weed Eater 96022000700, WE261, 96024000100 Assembly/Pre-Operation, Tools Required for Assembly

Page 7

ASSEMBLY/PRE-OPERATION

Your new riding mower has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your riding mower all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Stan­dard wrench sizes you need are listed below.

(1)3/4" wrench

(1)1/2" wrench

(1)Utility knife

(1)Tire pressure gauge

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steer- ing wheel).

TO REMOVE RIDING MOWER FROM CARTON

UNPACK CARTON

1.Cut along dotted lines on all four panels of carton. Remove carton and top frame as one unit.

2.Remove packing materials from riding mower.

NOTE: Only cut carton with a short blade utility knife, a long blade or saw can puncture tires on unit.

HOW TO SET UP YOUR RIDING MOWER

INSTALL STEERING COLUMN

1.Insert steering shaft into mount and se- curely fasten with bolt, washer, and nut provided.

2.Insert pin into hole in steering shaft.

3.Slide plastic cover over steering shaft and into position.

Steering Shaft

Plastic Cover

4.Slide steering shaft protective foam cover over shaft.

5.Position front wheels of the riding mower so they are pointing straight forward.

Insert

Nut

 

Washer

Steering Wheel

 

Adapter

 

Foam Cover

Steering Shaft

6.Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft.

7.Press steering wheel into position on shaft, install large washer, and tighten nut securely.

8.Snap steering wheel insert into center of steering wheel securely.

INSTALL SEAT

1.Pivot seat upward and remove from the cardboard packing. Remove the card- board packing and discard.

2.Place seat on seat pan so head of shoul- der bolt is positioned over large slotted hole in pan.

3.Push down on seat to engage shoulder bolt in slot and pull seat towards rear of riding mower.

Pin

Steering

Seat

 

Washer

Shaft

 

 

Mount

 

Nut

Bolt

Seat Pan

 

 

Shoulder

Bolt

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents WE261 Warranty Table of ContentsAlways wear eye protection when operat- ing machine Safety RulesGeneral Operation II. Slope Operation IV. Service Safe Handling of GasolineIII. Children Never operate machine in a closed area General ServiceCustomer Responsibilities Product SpecificationsRead and observe the safety rules Unassembled PartsTo Remove Riding Mower from Carton ASSEMBLY/PRE-OPERATIONTools Required for Assembly HOW to SET UP Your Riding Mower Install Steering ColumnCheck for Proper Positon of Mower Drive Belt Check BatteryCheck Tire Pressure Check Deck LevelnessCHECKLIST Operation ROS Know Your Riding MowerStopping HOW to USE Your Riding MowerTo Adjust Mower Cutting Height To SET Parking BrakeDisengage deck clutch lever Using the Reverse Operation SystemTo Operate Mower To Stop Mower BladeTo Start Engine Before Starting the EngineRecoil Starting System Mowing TipsGeneral Recommendations MaintenanceBefore Each USE Axle and Spindles Riding MowerBrake Operation TiresEngine BeltAIR Filter To Remove Mower Service and AdjustmentsTo Install Mower Riding MowerTo Replace Mower Blade Drive Belt To Level Mower HousingSIDE-TO-SIDE Adjustment FRONT-TO-BACK AdjustmentReplacing Battery To Adjust BrakeTo Adjust Steering Wheel Alignment To Start Engine with a Weak BatteryInterlocks and Relays EngineTo Replace Fuse Other BatteryStorage MowerProblem Cause Correction Troubleshooting ChartEngine continues to Riding Mower -CATALOG NO. WE261 SchematicElectrical KEY Part Description Chassis PAN, Seat Drive Service KIT, Transaxle Steering Wheel ASM Front Mower Deck Mandrel ASM Decals Suggested Guide for Sighting Slopes for Safe Operation Parts and Service
Related manuals
Manual 26 pages 24.19 Kb Manual 20 pages 13.36 Kb

96024000100, 532 43 32-03, 96022000700, WE261 specifications

The Weed Eater WE261 is a robust and versatile string trimmer designed to tackle a variety of lawn care tasks with ease and efficiency. Aimed at both homeowners and landscaping professionals, the WE261 is built to handle the challenges of overgrown lawns and garden beds, providing powerful performance and reliability.

One of the standout features of the WE261 is its 26cc 2-cycle engine, which delivers ample power while maintaining a lightweight profile. This engine ensures that users can navigate through dense vegetation and thick weeds without compromising performance. The 2-cycle technology allows for efficient fuel usage, providing users with longer run times between refuels.

The WE261 is equipped with a dual line bump head, which automatically releases more line as needed. This feature enhances productivity by allowing the user to focus on trimming rather than manually adjusting the string. The .095-inch line diameter provides a thick cutting path, making it effective against stubborn weeds and tall grass.

Another significant characteristic of the WE261 is its ergonomic design. The trimmer features a padded hand grip and an adjustable handle, allowing users to customize their grip for maximum comfort and control. This is especially beneficial during extended use, as it minimizes fatigue and enhances maneuverability.

The trimmer also incorporates an easy-start technology, which simplifies the starting process. Users can enjoy quick and hassle-free starts with minimal effort required. This feature is particularly useful for those who may not have extensive experience with starting gas-powered equipment.

Durability is a key consideration in the design of the WE261. Constructed with high-quality materials, this weed eater is built to withstand the rigors of regular use. The robust build ensures that it can handle various outdoor conditions, making it a reliable option for any lawn care enthusiast.

In summary, the Weed Eater WE261 presents a combination of power, efficiency, and user-friendly features. With its strong 26cc engine, automatic dual line bump head, ergonomic design, and easy-start technology, it stands out as an exceptional choice for anyone looking to maintain a well-groomed lawn. Whether dealing with overgrown areas or simply keeping the yard tidy, the WE261 is up to the task, delivering performance that users can trust.
Top Page Image Contents