Weed Eater WE165T42A manual Before Starting the Engine, To Operate on Hills, To Transport

Page 12

OPERATION

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground.Install gauge wheel in appropriate hole with shoulder bolt, 17/32 washer, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

GAUGE

WHEEL

MOUNTING

BRACKET

3/8-16

LOCKNUT

3/8 WASHER

SHOULDER

GAUGE WHEEL

BOLT

 

17/32 WASHER

FIG. 6

TO OPERATE MOWER (See Fig. 7)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

"ENGAGED" POSITION

 

ATTACHMENT

 

LIFT LEVER

 

HIGH POSITION

 

LOW

ATTACHMENT

POSITION

 

CLUTCH LEVER

 

"DISENGAGED"

 

POSITION

 

 

DEFLECTOR

 

SHIELD

FIG. 7

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Make all turns slowly.

TO TRANSPORT

•Raise attachment lift to highest position with attachment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

•The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model NO. WE165T42A Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Operate on HillsTo Transport Towing Carts and Other ATTACH- MentsMowing Tips ADD GasolineTo Start Engine See Fig Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Clean AIR Screen EngineBelts Transaxle CoolingCleaning Engine Cooling Fins SeeMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Check and Adjust Brake See Fig To Adjust BrakeTo Replace Motion Drive Belt See Fig To Check BrakeTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WE165T42A, Product no 57Electrical KEY Part Description Chassis and Enclosures Repair Parts Drive Transaxle Peerless Model Steering Assembly Repair Parts Engine Repair Parts Seat Assembly Decals Wheels & TiresMower Lift Repair Parts Mower Deck CAB Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

WE165T42A specifications

The Weed Eater WE165T42A is a versatile and efficient lawn care tool designed to tackle various tasks in maintaining a tidy garden. This product is particularly favored by homeowners for its durability, ease of use, and impressive performance. One of its standout features is the powerful 16-inch cutting path, which ensures that users can cover large areas quickly. This makes it an ideal choice for those looking to maintain their lawns without spending excessive time on yard work.

A key feature of the WE165T42A is its gas-powered engine, which provides reliable power and performance. This engine allows the trimmer to easily cut through thick grass, weeds, and even light brush, ensuring that your garden remains well-maintained. The unit is designed with a robust build, ensuring it can withstand the rigors of regular use while also being lightweight enough for comfortable handling.

Ease of operation is another significant aspect of the Weed Eater WE165T42A. It includes a simple starting system that makes it easy for users to get the machine running with minimal effort. The adjustable handle adds comfort and flexibility, allowing users to find their ideal operating position, which can help reduce fatigue during extended use.

Another notable technology within the WE165T42A is its dual-line feed head. This feature not only provides improved cutting efficiency but also allows for a wider cutting path, reducing the time spent on each trimming session. The trimmer line automatically feeds out as needed, ensuring that users do not have to stop work to manually adjust the line length.

The Weed Eater WE165T42A is also designed with user safety in mind. It includes protective features such as a debris guard, which deflects all the debris away from the operator for a safer working environment. This is especially important when dealing with tougher growth, which can send rocks and other materials flying.

In conclusion, the Weed Eater WE165T42A stands out in the lawn care market for its combination of power, efficiency, and user-friendly features. Its durable construction, ease of operation, and advanced technologies make it an excellent choice for homeowners who value both performance and practicality in their lawn maintenance tools. Whether tackling a small patio garden or a larger yard, the WE165T42A is up to the task, making lawn care simpler and more efficient.
Top Page Image Contents