Weed Eater WE165T42A manual To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig

Page 19

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 17 and 18)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 17

SUSPENSION ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 18

FRONT-TO-BACK ADJUSTMENT (See Figs. 19 and 20)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

“D”

“D”

FIG. 19

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “F”

NUT “E”

TRUNNION

FRONT LINKS

FIG. 20

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 21)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instruc- tions.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model NO. WE165T42A Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other ATTACH- Ments Before Starting the EngineTo Operate on Hills To TransportADD Gasoline Mowing TipsTo Start Engine See Fig Before Each USE MaintenanceLubrication Chart General RecommendationsTractor Transaxle Cooling Clean AIR ScreenEngine BeltsSpark Plugs CleaningEngine Cooling Fins See MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTo Remove Wheel for Repairs See Fig To Remove CABLES, Reverse Order To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WE165T42A, Product no 57 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Drive Transaxle Peerless Model Steering Assembly Repair Parts Engine Repair Parts Seat Assembly Wheels & Tires DecalsMower Lift Repair Parts Mower Deck CAB Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

WE165T42A specifications

The Weed Eater WE165T42A is a versatile and efficient lawn care tool designed to tackle various tasks in maintaining a tidy garden. This product is particularly favored by homeowners for its durability, ease of use, and impressive performance. One of its standout features is the powerful 16-inch cutting path, which ensures that users can cover large areas quickly. This makes it an ideal choice for those looking to maintain their lawns without spending excessive time on yard work.

A key feature of the WE165T42A is its gas-powered engine, which provides reliable power and performance. This engine allows the trimmer to easily cut through thick grass, weeds, and even light brush, ensuring that your garden remains well-maintained. The unit is designed with a robust build, ensuring it can withstand the rigors of regular use while also being lightweight enough for comfortable handling.

Ease of operation is another significant aspect of the Weed Eater WE165T42A. It includes a simple starting system that makes it easy for users to get the machine running with minimal effort. The adjustable handle adds comfort and flexibility, allowing users to find their ideal operating position, which can help reduce fatigue during extended use.

Another notable technology within the WE165T42A is its dual-line feed head. This feature not only provides improved cutting efficiency but also allows for a wider cutting path, reducing the time spent on each trimming session. The trimmer line automatically feeds out as needed, ensuring that users do not have to stop work to manually adjust the line length.

The Weed Eater WE165T42A is also designed with user safety in mind. It includes protective features such as a debris guard, which deflects all the debris away from the operator for a safer working environment. This is especially important when dealing with tougher growth, which can send rocks and other materials flying.

In conclusion, the Weed Eater WE165T42A stands out in the lawn care market for its combination of power, efficiency, and user-friendly features. Its durable construction, ease of operation, and advanced technologies make it an excellent choice for homeowners who value both performance and practicality in their lawn maintenance tools. Whether tackling a small patio garden or a larger yard, the WE165T42A is up to the task, making lawn care simpler and more efficient.
Top Page Image Contents