Weed Eater WE165T42A manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 28)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

 

HEADLIGHT

HOOD

WIRE

CONNECTOR

FIG. 28

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 29)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that hole in throttle lever and hole in plate line up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned.Tighten clamp screw securely.

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary.However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - dam- age may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.OVERSPEEDINGTHE ENGINE ABOVETHE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACTYOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

IDLE SPEED SCREW

PLATE

THROTTLE CABLE

CLAMP

SCREW

HOLE “A”

THROTTLE LEVER

FAST

FIG. 29

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. WE165T42A Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other ATTACH- Ments Before Starting the EngineTo Operate on Hills To TransportTo Start Engine See Fig Mowing TipsADD Gasoline Before Each USE MaintenanceLubrication Chart General RecommendationsTractor Transaxle Cooling Clean AIR ScreenEngine BeltsSpark Plugs CleaningEngine Cooling Fins See MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Remove CABLES, Reverse Order To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WE165T42A, Product no 57 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Drive Transaxle Peerless Model Steering Assembly Repair Parts Engine Repair Parts Seat Assembly Wheels & Tires DecalsMower Lift Repair Parts Mower Deck CAB Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

WE165T42A specifications

The Weed Eater WE165T42A is a versatile and efficient lawn care tool designed to tackle various tasks in maintaining a tidy garden. This product is particularly favored by homeowners for its durability, ease of use, and impressive performance. One of its standout features is the powerful 16-inch cutting path, which ensures that users can cover large areas quickly. This makes it an ideal choice for those looking to maintain their lawns without spending excessive time on yard work.

A key feature of the WE165T42A is its gas-powered engine, which provides reliable power and performance. This engine allows the trimmer to easily cut through thick grass, weeds, and even light brush, ensuring that your garden remains well-maintained. The unit is designed with a robust build, ensuring it can withstand the rigors of regular use while also being lightweight enough for comfortable handling.

Ease of operation is another significant aspect of the Weed Eater WE165T42A. It includes a simple starting system that makes it easy for users to get the machine running with minimal effort. The adjustable handle adds comfort and flexibility, allowing users to find their ideal operating position, which can help reduce fatigue during extended use.

Another notable technology within the WE165T42A is its dual-line feed head. This feature not only provides improved cutting efficiency but also allows for a wider cutting path, reducing the time spent on each trimming session. The trimmer line automatically feeds out as needed, ensuring that users do not have to stop work to manually adjust the line length.

The Weed Eater WE165T42A is also designed with user safety in mind. It includes protective features such as a debris guard, which deflects all the debris away from the operator for a safer working environment. This is especially important when dealing with tougher growth, which can send rocks and other materials flying.

In conclusion, the Weed Eater WE165T42A stands out in the lawn care market for its combination of power, efficiency, and user-friendly features. Its durable construction, ease of operation, and advanced technologies make it an excellent choice for homeowners who value both performance and practicality in their lawn maintenance tools. Whether tackling a small patio garden or a larger yard, the WE165T42A is up to the task, making lawn care simpler and more efficient.
Top Page Image Contents