Weed Eater 184071 manual Tractor, Brake Operation, Tires, Operator Presence System, Blade Care

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 8)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer se- curing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

MANDREL

TRAILINGASSEMBLY EDGE UP

CENTER

HOLE

LOCK WASHER

STAR

FLAT WASHER

BLADE

 

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 8

TO SHARPEN BLADE (See Fig. 9)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 9

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model NO. WE12538M II. Slope Operation Safety RulesIV. Service General OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Steering Wheel Seat Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Check Engine OIL Level Before Starting the EngineTo Operate on Hills To Transport Towing Carts and Other ATTACH- MentsTo Start Engine See Fig Mowing TipsGeneral Recommendations MaintenanceLubrication Chart Service DatesOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsClean AIR Screen Engine Cooling Fins See FigAIR Filter See Fig IN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER To Check and Adjust Brake See FigTo Adjust Steering Wheel ALIGN- Ment To Replace Motion Drive Belt See FigTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove Wheel for Repairs See FigTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WE12538M, Product no 56 SchematicElectrical KEY Part Description Chassis Repair Parts Drive Transaxle Steering 183226 Optional Equipment 170551 Control Th/ch Flag Seat Wheels & Tires DecalsMower Lift Repair Parts Mower Deck CAB 178515Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

184071 specifications

The Weed Eater 184071 is a powerful and efficient string trimmer designed for homeowners and landscapers alike. Equipped with a robust 17-inch cutting width, it offers a wide swath for trimming grass and weeds, making lawn maintenance a quicker task. The lightweight design, weighing just around 10 pounds, ensures the trimmer is easy to maneuver, reducing strain during prolonged use.

One of the standout features of the Weed Eater 184071 is its innovative bump feed spool system. This design allows users to easily advance the line without having to stop and manually adjust it. By simply bumping the trimmer head on the ground, the user can release more line, ensuring a continuous and efficient trimming experience. This feature not only saves time but also enhances productivity, especially for larger yards.

The engine of the Weed Eater 184071 utilizes a 25cc two-stroke power plant that delivers reliable performance while maintaining fuel efficiency. This engine type is known for its capability to generate high torque, providing users with the power required to tackle tough overgrown areas with ease. Additionally, the trimmer’s engine is designed with reduced emissions in mind, aligning with environmental standards and promoting a greener approach to lawn care.

Comfort and ergonomics are crucial aspects of the Weed Eater 184071. The trimmer is equipped with a comfortable and adjustable handle that allows users to find their ideal grip, enhancing control and reducing fatigue. Furthermore, the lightweight nature of the tool means that it can be used for extended periods without causing undue stress on the body.

In terms of versatility, the Weed Eater 184071 is compatible with various attachments, allowing it to perform multiple functions beyond just trimming. This feature transforms the trimmer into a multi-tool that can handle different landscaping tasks, including edging and brush clearing, making it a valuable addition to any homeowner’s toolkit.

Overall, the Weed Eater 184071 is a well-rounded choice for those seeking a reliable and efficient solution for lawn care. With its combination of power, ease of use, and functionality, this string trimmer stands out as a leading option for maintaining a well-groomed yard. Whether managing a small garden or a larger property, the Weed Eater 184071 is designed to meet a variety of landscaping needs effectively and efficiently.
Top Page Image Contents