Weed Eater 184071 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse, Engine

Page 23

SERVICE AND ADJUSTMENTS

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 27)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 27

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 28)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

 

GOVERNOR

GOVERNOR

 

CONTROL PLATE

 

CONTROL LEVER

 

 

HOLES “A”

CLAMP

THROTTLE

 

SCREW

CABLE

 

 

FIG. 28

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - dam- age may result.

IMPORTANT:NEVERTAMPERWITHTHEENGINEGOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACTYOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. WE12538M II. Slope Operation Safety RulesIV. Service General OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Steering Wheel Seat Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Check Engine OIL Level Before Starting the EngineTo Operate on Hills To Transport Towing Carts and Other ATTACH- MentsTo Start Engine See Fig Mowing TipsGeneral Recommendations MaintenanceLubrication Chart Service DatesOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsAIR Filter See Fig Clean AIR ScreenEngine Cooling Fins See Fig IN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER To Check and Adjust Brake See FigTo Adjust Steering Wheel ALIGN- Ment To Replace Motion Drive Belt See FigTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove Wheel for Repairs See FigTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WE12538M, Product no 56 SchematicElectrical KEY Part Description Chassis Repair Parts Drive Transaxle Steering 183226 Optional Equipment 170551 Control Th/ch Flag Seat Wheels & Tires DecalsMower Lift Repair Parts Mower Deck CAB 178515Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

184071 specifications

The Weed Eater 184071 is a powerful and efficient string trimmer designed for homeowners and landscapers alike. Equipped with a robust 17-inch cutting width, it offers a wide swath for trimming grass and weeds, making lawn maintenance a quicker task. The lightweight design, weighing just around 10 pounds, ensures the trimmer is easy to maneuver, reducing strain during prolonged use.

One of the standout features of the Weed Eater 184071 is its innovative bump feed spool system. This design allows users to easily advance the line without having to stop and manually adjust it. By simply bumping the trimmer head on the ground, the user can release more line, ensuring a continuous and efficient trimming experience. This feature not only saves time but also enhances productivity, especially for larger yards.

The engine of the Weed Eater 184071 utilizes a 25cc two-stroke power plant that delivers reliable performance while maintaining fuel efficiency. This engine type is known for its capability to generate high torque, providing users with the power required to tackle tough overgrown areas with ease. Additionally, the trimmer’s engine is designed with reduced emissions in mind, aligning with environmental standards and promoting a greener approach to lawn care.

Comfort and ergonomics are crucial aspects of the Weed Eater 184071. The trimmer is equipped with a comfortable and adjustable handle that allows users to find their ideal grip, enhancing control and reducing fatigue. Furthermore, the lightweight nature of the tool means that it can be used for extended periods without causing undue stress on the body.

In terms of versatility, the Weed Eater 184071 is compatible with various attachments, allowing it to perform multiple functions beyond just trimming. This feature transforms the trimmer into a multi-tool that can handle different landscaping tasks, including edging and brush clearing, making it a valuable addition to any homeowner’s toolkit.

Overall, the Weed Eater 184071 is a well-rounded choice for those seeking a reliable and efficient solution for lawn care. With its combination of power, ease of use, and functionality, this string trimmer stands out as a leading option for maintaining a well-groomed yard. Whether managing a small garden or a larger property, the Weed Eater 184071 is designed to meet a variety of landscaping needs effectively and efficiently.
Top Page Image Contents