Weed Eater 184071 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

1/2" wrenches

Pliers

(1)

9/16" wrench

Tire pressure gauge

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

•Place tabs of steering boot over tab slots in dash and push down to secure.

 

INSERT

 

1/2 HEX NUT

 

LARGE FLAT

 

WASHER

STEERING

STEERING

BOOT

WHEEL

 

 

TABS

ADAPTER

 

 

EXTENSION SHAFT

 

1/4 HEX BOLT

1/4 LOCKNUT

 

LOWER

TAB

SLOTS

STEERING

 

SHAFT

 

FIG. 1

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 1/2 hex nut and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model NO. WE12538M General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering Wheel SeatTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other ATTACH- Ments Before Starting the EngineTo Operate on Hills To Transport Check Engine OIL LevelMowing Tips To Start Engine See FigService Dates MaintenanceLubrication Chart General RecommendationsTires TractorBrake Operation Operator Presence SystemBelts BatteryEngine Transaxle CoolingClean AIR Screen Engine Cooling Fins See FigAIR Filter See Fig Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WE12538M, Product no 56Electrical KEY Part Description Chassis Repair Parts Drive Transaxle Steering 183226 Optional Equipment 170551 Control Th/ch Flag Seat Decals Wheels & TiresMower Lift Repair Parts Mower Deck 178515 CABService Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

184071 specifications

The Weed Eater 184071 is a powerful and efficient string trimmer designed for homeowners and landscapers alike. Equipped with a robust 17-inch cutting width, it offers a wide swath for trimming grass and weeds, making lawn maintenance a quicker task. The lightweight design, weighing just around 10 pounds, ensures the trimmer is easy to maneuver, reducing strain during prolonged use.

One of the standout features of the Weed Eater 184071 is its innovative bump feed spool system. This design allows users to easily advance the line without having to stop and manually adjust it. By simply bumping the trimmer head on the ground, the user can release more line, ensuring a continuous and efficient trimming experience. This feature not only saves time but also enhances productivity, especially for larger yards.

The engine of the Weed Eater 184071 utilizes a 25cc two-stroke power plant that delivers reliable performance while maintaining fuel efficiency. This engine type is known for its capability to generate high torque, providing users with the power required to tackle tough overgrown areas with ease. Additionally, the trimmer’s engine is designed with reduced emissions in mind, aligning with environmental standards and promoting a greener approach to lawn care.

Comfort and ergonomics are crucial aspects of the Weed Eater 184071. The trimmer is equipped with a comfortable and adjustable handle that allows users to find their ideal grip, enhancing control and reducing fatigue. Furthermore, the lightweight nature of the tool means that it can be used for extended periods without causing undue stress on the body.

In terms of versatility, the Weed Eater 184071 is compatible with various attachments, allowing it to perform multiple functions beyond just trimming. This feature transforms the trimmer into a multi-tool that can handle different landscaping tasks, including edging and brush clearing, making it a valuable addition to any homeowner’s toolkit.

Overall, the Weed Eater 184071 is a well-rounded choice for those seeking a reliable and efficient solution for lawn care. With its combination of power, ease of use, and functionality, this string trimmer stands out as a leading option for maintaining a well-groomed yard. Whether managing a small garden or a larger property, the Weed Eater 184071 is designed to meet a variety of landscaping needs effectively and efficiently.
Top Page Image Contents