Weed Eater 186913 manual Off

Page 26

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

 

CORRECTION

Engine continues to run

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not

when operator leaves

 

 

 

corrected, contact an authorized service center/

seat with attachment

 

 

 

department.

clutch engaged

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Mower deck not level.

2.

Level mower deck.

 

3.

Buildup of grass, leaves, and trash under mower.

3.

Clean underside of mower housing.

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

5.

Clogged mower deck vent holes from buildup of

5.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Mower blades will not

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

Poor grass discharge

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

4.

Mower deck not level.

4.

Level mower deck.

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

6.

Worn, bent or loose blade.

6.

Replace/sharpen blade. Tighten blade bolt.

 

7.

Buildup of grass, leaves and trash under mower.

7.

Clean underside of mower housing.

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

10.

Improper blades used.

10.

Replace with blades listed in this manual.

 

11.

Clogged mower deck vent holes from buildup of

11.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Headlight(s) not working

1.

Switch is “OFF”.

1.

Turn switch “ON”.

(if so equipped)

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

3.

Faulty light switch.

3.

Check/replace light switch.

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

Battery will not charge

1.

Bad battery cell(s).

1.

Replace battery.

 

2.

Poor cable connections.

2.

Check/clean all connections.

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

Loss of drive

1.

Freewheel control in “disengaged” position.

1.

Place freewheel control in “engaged” position.

 

2.

Motion drive belt worn, damaged, or broken.

2.

Replace motion drive belt.

 

3.

Air trapped in transmission during shipment

3.

Purge transmission.

 

 

or servicing.

 

 

 

 

 

 

 

Engine “backfires”

1.

Engine throttle control not set at “SLOW”

1.

Move throttle control to “SLOW” position and allow

when turning engine

 

position for 30 seconds before stopping engine.

 

to idle for 30 seconds before stopping engine.

“OFF”

 

 

 

 

 

 

 

 

 

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Model NO. WET17H42STA General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Table of Contents Key Unassembled PartsSteering Wheel Seat Slope SheetHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CAR- TONCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Before Starting the EngineTo Operate Mower See Fig To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips General Recommendations MaintenanceLubrication Chart Before Each USETractor Engine AIR Filter CleaningEngine Cooling Fins MufflerTo Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Adjust Brake To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigReplacing Battery See Figs Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Carburetor Interlocks and RelaysFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WET17H42STATractor - Model Number WET17H42STA Electrical KEY Part NO. NO. Description Tractor - Model Number WET17H42STA Chassis and Enclosures KEY Part Description Tractor - Model Number WET17H42STA Drive Repair Parts Tractor - Model Number WET17H42STA Steering Assembly KEY Part NO. NO. Description Tractor - Model Number WET17H42STA Engine Optional EquipmentTractor - Model Number WET17H42STA Seat Assembly Tractor - Model Number WET17H42STA Decals Wheels & TiresTractor - Model Number WET17H42STA Mower Lift 173288 Link FrontTractor - Model Number WET17H42STA Mower Deck 165892 Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty

186913 specifications

The Weed Eater 186913 is a remarkable addition to the world of outdoor power equipment, specifically designed to tackle the challenges of yard maintenance with precision and ease. This versatile and powerful string trimmer stands out for its user-friendly features and advanced technologies.

At the heart of the Weed Eater 186913 is its robust 25cc two-cycle engine, delivering a strong performance that ensures your lawn looks pristine. This high-performance engine provides an impressive power-to-weight ratio, making it easy to maneuver around your yard while maintaining impressive cutting capability. With a quick-start feature, users can expect minimal effort when firing up the trimmer, allowing for more time spent trimming and less time struggling with start-ups.

One of the key characteristics of the Weed Eater 186913 is its lightweight design. Weighing in at just 10 pounds, it reduces fatigue during extended use, making it an ideal choice for both homeowners and professionals. Additionally, the trimmer is equipped with an adjustable handle that can be tailored to suit the user's height and comfort, further enhancing the overall experience.

The Weed Eater 186913 employs a dual-line cutting system that allows for efficient trimming of grass and weeds. The automatic feed spool releases line as needed, minimizing interruptions and maximizing productivity. This technology ensures that the user can maintain a consistent cutting length without the hassle of manual line adjustments, making it a time-saver in outdoor maintenance.

Durability is another hallmark of the Weed Eater 186913. The trimmer is constructed with high-quality materials, ensuring longevity and reliability even under rigorous conditions. This makes it an excellent investment for those who require a dependable tool to tackle their landscaping needs.

For enhanced control and precision, the Weed Eater 186913 features a curved shaft design, allowing for easy navigation around flower beds and tight corners. This ergonomic design helps users achieve professional-looking results without the discomfort commonly associated with traditional straight-shaft models.

In conclusion, the Weed Eater 186913 combines power, convenience, and durability into one efficient package, making it an excellent choice for anyone in need of a reliable string trimmer. With its advanced engine technology, user-friendly features, and thoughtful design, it stands ready to help you maintain a beautiful and well-manicured lawn. Whether tackling overgrown weeds or edging along sidewalks, the Weed Eater 186913 is equipped to handle the job with ease.
Top Page Image Contents