Weed Eater 186913 manual Tools Required for Assembly, To Remove Tractor from CAR- TON

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

Pliers

(2)

7/16" wrenches

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CAR- TON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (SEE FIG. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

 

INSERT

 

1/2 LOCK WASHER

 

LARGE FLAT

 

WASHER

STEERING

 

WHEEL

 

 

STEERING

 

BOOT

 

TABS

ADAPTER

EXTENSION SHAFT

 

 

1/4 HEX BOLT

1/4 LOCKNUT

 

LOWER

 

STEERING

 

SHAFT

 

 

TAB

 

SLOTS

FIG. 1

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 1/2 hex nut and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

HOW TO SET UP YOUR TRACTOR

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and flat washer loosely. Do not tighten

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model NO. WET17H42STA General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Table of Contents Key Unassembled PartsSteering Wheel Seat Slope SheetHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CAR- TONCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Before Starting the EngineTo Operate Mower See Fig To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips General Recommendations MaintenanceLubrication Chart Before Each USETractor Engine AIR Filter CleaningEngine Cooling Fins MufflerTo Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal To Adjust Brake To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigReplacing Battery See Figs Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Carburetor Interlocks and RelaysFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WET17H42STATractor - Model Number WET17H42STA Electrical KEY Part NO. NO. Description Tractor - Model Number WET17H42STA Chassis and Enclosures KEY Part Description Tractor - Model Number WET17H42STA Drive Repair Parts Tractor - Model Number WET17H42STA Steering Assembly KEY Part NO. NO. Description Tractor - Model Number WET17H42STA Engine Optional EquipmentTractor - Model Number WET17H42STA Seat Assembly Tractor - Model Number WET17H42STA Decals Wheels & TiresTractor - Model Number WET17H42STA Mower Lift 173288 Link FrontTractor - Model Number WET17H42STA Mower Deck 165892 Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty

186913 specifications

The Weed Eater 186913 is a remarkable addition to the world of outdoor power equipment, specifically designed to tackle the challenges of yard maintenance with precision and ease. This versatile and powerful string trimmer stands out for its user-friendly features and advanced technologies.

At the heart of the Weed Eater 186913 is its robust 25cc two-cycle engine, delivering a strong performance that ensures your lawn looks pristine. This high-performance engine provides an impressive power-to-weight ratio, making it easy to maneuver around your yard while maintaining impressive cutting capability. With a quick-start feature, users can expect minimal effort when firing up the trimmer, allowing for more time spent trimming and less time struggling with start-ups.

One of the key characteristics of the Weed Eater 186913 is its lightweight design. Weighing in at just 10 pounds, it reduces fatigue during extended use, making it an ideal choice for both homeowners and professionals. Additionally, the trimmer is equipped with an adjustable handle that can be tailored to suit the user's height and comfort, further enhancing the overall experience.

The Weed Eater 186913 employs a dual-line cutting system that allows for efficient trimming of grass and weeds. The automatic feed spool releases line as needed, minimizing interruptions and maximizing productivity. This technology ensures that the user can maintain a consistent cutting length without the hassle of manual line adjustments, making it a time-saver in outdoor maintenance.

Durability is another hallmark of the Weed Eater 186913. The trimmer is constructed with high-quality materials, ensuring longevity and reliability even under rigorous conditions. This makes it an excellent investment for those who require a dependable tool to tackle their landscaping needs.

For enhanced control and precision, the Weed Eater 186913 features a curved shaft design, allowing for easy navigation around flower beds and tight corners. This ergonomic design helps users achieve professional-looking results without the discomfort commonly associated with traditional straight-shaft models.

In conclusion, the Weed Eater 186913 combines power, convenience, and durability into one efficient package, making it an excellent choice for anyone in need of a reliable string trimmer. With its advanced engine technology, user-friendly features, and thoughtful design, it stands ready to help you maintain a beautiful and well-manicured lawn. Whether tackling overgrown weeds or edging along sidewalks, the Weed Eater 186913 is equipped to handle the job with ease.
Top Page Image Contents