Weed Eater 186913 manual ADD Gasoline, To Start Engine See Fig, Purge Transmission

Page 13

OPERATION

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 4)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place motion control lever in neutral (N) position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to“START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast posi- tion. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Place the motion control lever in neutral. Release the parking brake and let the clutch/

brake slowly return to operating position.

•Allow one minute for transmission to warm up.This can be done during the engine warm up period.

•The attachments can also be used during the engine warm-up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run- ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on level surface with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly dis- engage clutch/brake pedal.

•Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model NO. WET17H42STA IV. Service Safety RulesGeneral Operation II. Slope OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsKey Slope SheetTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Before Starting the EngineTo Operate on Hills To Transport See FigsTo Start Engine See Fig ADD GasolinePurge Transmission Automatic Transmission Warm UPMowing Tips Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine Engine Cooling Fins CleaningAIR Filter MufflerTo Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal Transaxle Motion Control Lever Neutral Adjustment See Fig To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Replace Headlight Bulb Interlocks and RelaysOther StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number WET17H42STA SchematicTractor - Model Number WET17H42STA Electrical KEY Part NO. NO. Description Tractor - Model Number WET17H42STA Chassis and Enclosures KEY Part Description Tractor - Model Number WET17H42STA Drive Repair Parts Tractor - Model Number WET17H42STA Steering Assembly KEY Part NO. NO. Description Optional Equipment Tractor - Model Number WET17H42STA EngineTractor - Model Number WET17H42STA Seat Assembly Wheels & Tires Tractor - Model Number WET17H42STA Decals173288 Link Front Tractor - Model Number WET17H42STA Mower LiftTractor - Model Number WET17H42STA Mower Deck 165892 Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationLimited Warranty

186913 specifications

The Weed Eater 186913 is a remarkable addition to the world of outdoor power equipment, specifically designed to tackle the challenges of yard maintenance with precision and ease. This versatile and powerful string trimmer stands out for its user-friendly features and advanced technologies.

At the heart of the Weed Eater 186913 is its robust 25cc two-cycle engine, delivering a strong performance that ensures your lawn looks pristine. This high-performance engine provides an impressive power-to-weight ratio, making it easy to maneuver around your yard while maintaining impressive cutting capability. With a quick-start feature, users can expect minimal effort when firing up the trimmer, allowing for more time spent trimming and less time struggling with start-ups.

One of the key characteristics of the Weed Eater 186913 is its lightweight design. Weighing in at just 10 pounds, it reduces fatigue during extended use, making it an ideal choice for both homeowners and professionals. Additionally, the trimmer is equipped with an adjustable handle that can be tailored to suit the user's height and comfort, further enhancing the overall experience.

The Weed Eater 186913 employs a dual-line cutting system that allows for efficient trimming of grass and weeds. The automatic feed spool releases line as needed, minimizing interruptions and maximizing productivity. This technology ensures that the user can maintain a consistent cutting length without the hassle of manual line adjustments, making it a time-saver in outdoor maintenance.

Durability is another hallmark of the Weed Eater 186913. The trimmer is constructed with high-quality materials, ensuring longevity and reliability even under rigorous conditions. This makes it an excellent investment for those who require a dependable tool to tackle their landscaping needs.

For enhanced control and precision, the Weed Eater 186913 features a curved shaft design, allowing for easy navigation around flower beds and tight corners. This ergonomic design helps users achieve professional-looking results without the discomfort commonly associated with traditional straight-shaft models.

In conclusion, the Weed Eater 186913 combines power, convenience, and durability into one efficient package, making it an excellent choice for anyone in need of a reliable string trimmer. With its advanced engine technology, user-friendly features, and thoughtful design, it stands ready to help you maintain a beautiful and well-manicured lawn. Whether tackling overgrown weeds or edging along sidewalks, the Weed Eater 186913 is equipped to handle the job with ease.
Top Page Image Contents