Pioneer BDP-05FD operating instructions Troubleshooting, Playback, Problem Check Remedy

Chapter 7	07
Additional information

Troubleshooting

Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble cannot be rectified after checking the items below, please contact customer services. In the US, call Toll Free (800) 421-1404.

(Telephone lines are open Monday through Friday 6:00 AM to 4:30 PM (Pacific Time).) In Canada, call Local (905) 479-4411, or Long distance +1(877) 283-5901. (Telephone lines are open Monday through Friday 9:00 AM to 5:30 PM (EST).)

Playback

Problem	Check	Remedy
Disc does not play.	Is the disc scratched?	It may not be possible to play scratched discs.
Disc tray opens
	Is the disc dirty?	Clean the disc (page 59).
automatically.
	Is the disc properly set in the disc tray?	• Set the disc with the printed side facing up.
		• Set the disc properly in the depression in the disc tray.
	Is the region number correct?	The region numbers of discs that can be played on this set are
		as shown below (page 10).
		• BDs: “A” (or including “A”) and “ALL”
		• DVDs: “1” (or including “1”) and “ALL”
	Is the player set in a humid place?	There could be condensation inside. Wait for the condensation
		to dissipate. Do not set the player near an air-conditioner, etc.
		(page 58).
Picture freezes and the front		• Press  STOP to stop playback, then restart playback.
panel and remote control		• If the playback cannot be stopped, press  STANDBY/ON
buttons stop working.		on the player’s front panel to turn off the power, then turn the
		power back on.
		• If the power cannot be turned off, press and hold
		 STANDBY/ON on the player’s front panel for over 5
		seconds. The power will turn off.
No picture is displayed or the	Is the video cable properly connected?	Insert the cable firmly and all the way in.
picture is not displayed
	Is the video cable damaged?	If the cable is damaged, replace it with a new one.
properly.
	Is the input setting on the connected TV or AV receiver or	Read the operating instructions of the connected components
	amplifier right?	and switch to the proper input.
	Are the terminals for outputting video signals properly set?	Press VIDEO SELECT to switch the terminal from which the
		video signals are output.

Is the output video resolution properly set?

Depending on the player’s output video resolution, the picture may not be displayed at all or displayed properly. Use OUTPUT RESOLUTION to switch to a resolution at which the picture is displayed properly (page 25).

	Is the player connected with an HDMI cable other than a High	Press while pressing on the player’s front panel to restore
	Speed HDMI™ cable (with a Standard HDMI™ cable)?	the video outputs to the factory default settings. After use
		Setup Navigator to reset the player.
		There are some BDs for which the picture will only be output
		when connected by HDMI cable.
Picture is stretched.	Is the TV’s aspect ratio properly set?	Read the TV’s operating instructions and set the TV’s aspect
Aspect ratio cannot be		ratio properly.
switched.	Is 4:3 Video Out properly set?	• Set 4:3 Video Out properly (page 40).
		• When video signals with a resolution of 1080/60i, 1080/60p,
		1080/24p or 720/60p are being output from the HDMI OUT
		terminal or the COMPONENT VIDEO output terminals, they
		may be output in the 16:9 (Widescreen) mode even if TV
		Aspect Ratio is set to 4:3 (Standard) (page 25).
Sound and picture are not	Is Output Terminal Priority properly set?	Set Output Terminal Priority properly (pages 20 and 48).
synchronized.			51

En