Weed Eater 191064 manual Mowing Tips, To Start Engine See Fig

Page 13

OPERATION

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 5)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place gear shift lever in neutral (N) position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke () position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to“START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke ( ) position and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke () position until the engine runs roughly, then move throttle control to fast position.This may require an engine warm-up period from several seconds to several minutes, depending on the tem- perature.

•The attachments can also be used during the engine warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

MOWING TIPS

•Mower should be properly leveled for best mowing per- formance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 7).

00272

FIG. 7

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by se- lecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model NO. WET1742STB Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Install Seat See FigCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsLubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine Muffler CleaningSpark Plugs IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigReplacing Battery See Figs To Start Engine with a Weak Battery See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILTroubleshooting Points With attachment clutch Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

191064 specifications

The Weed Eater 191064 is a powerful and efficient tool designed for both residential and commercial lawn care. This gas-powered string trimmer is known for its robust design and user-friendly features, making it a popular choice among gardening enthusiasts and professionals alike.

One of the standout features of the Weed Eater 191064 is its lightweight construction, which significantly reduces operator fatigue during extended use. The ergonomic design ensures a comfortable grip, allowing users to maneuver around gardens, flower beds, and hard-to-reach areas with ease. The trimmer is equipped with a 28cc two-cycle engine that provides ample power for tackling even the most challenging weeds and overgrowth.

In terms of technology, the Weed Eater 191064 utilizes a bump feed system to release cutting line. This user-friendly feature allows you to simply tap the trimmer head on the ground while in operation to release more line as needed, ensuring uninterrupted work without the hassle of constantly stopping to adjust the line. This mechanism not only boosts productivity but also enhances overall efficiency.

The trimmer boasts a dual line cut, meaning it uses two lines simultaneously, allowing for a wider cutting swath. This feature leads to faster trimming times, making it an ideal choice for large yards or commercial landscaping jobs. Moreover, the Weed Eater 191064 is designed to accept a variety of different cutting attachments, giving users the flexibility to switch between trimming, edging, and even brush cutting as needed.

The engine is also designed with fuel efficiency in mind. The Weed Eater 191064 uses a fuel-efficient two-cycle engine that reduces fuel consumption while still delivering high torque power. This translates to lower running costs and, importantly, a reduced environmental impact compared to some competitors.

The ease of maintenance is another significant characteristic of the Weed Eater 191064. With accessible parts and straightforward assembly, users can quickly perform regular upkeep, ensuring the longevity and performance of the trimmer.

Overall, the Weed Eater 191064 is a versatile and user-friendly trimmer that excels in performance, making it a valuable addition to any landscaping toolkit. Whether for a homeowner wanting to maintain their yard or a professional needing reliable equipment, this trimmer delivers on all fronts.
Top Page Image Contents