Weed Eater 191064 manual Troubleshooting Points

Page 25

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

 

CORRECTION

 

 

 

 

 

 

Will not start

1.

Out of fuel.

1.

Fill fuel tank.

 

2.

Engine not “CHOKED” properly.

2.

See “TO START ENGINE” in Operation section.

 

3.

Engine flooded.

3.

Wait several minutes before attempting to start.

 

4.

Bad spark plug.

4.

Replace spark plug.

 

5.

Dirty air filter.

5.

Clean/replace air filter.

 

6.

Dirty fuel filter.

6.

Replace fuel filter.

 

7.

Water in fuel.

7.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

8.

Loose or damaged wiring.

8.

Check all wiring.

 

9.

Carburetor out of adjustment.

9.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

10.

Engine valves out of adjustment.

10.

Contact an authorized service center/department.

 

 

 

 

 

 

Hard to start

1.

Dirty air filter.

1.

Clean/replace air filter.

 

2.

Bad spark plug.

2.

Replace spark plug.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Dirty fuel filter.

4.

Replace fuel filter.

 

5.

Stale or dirty fuel.

5.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Carburetor out of adjustment.

7.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

8.

Engine valves out of adjustment.

8.

Contact an authorized service center/department.

 

 

 

 

 

 

Engine will not turn over

1.

Clutch/brake pedal not depressed.

1.

Depress clutch/brake pedal.

 

2.

Attachment clutch is engaged.

2.

Disengage attachment clutch.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Blown fuse.

4.

Replace fuse.

 

5.

Corroded battery terminals.

5.

Clean battery terminals.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Faulty ignition switch.

7.

Check/replace ignition switch.

 

8.

Faulty solenoid or starter.

8.

Check/replace solenoid or starter.

 

9.

Faulty operator presence switch(es).

9.

Contact an authorized service center/department.

 

 

 

 

 

 

Engine clicks but will not

1.

Weak or dead battery.

1.

Recharge or replace battery.

start

2.

Corroded battery terminals.

2.

Clean battery terminals.

 

3.

Loose or damaged wiring.

3.

Check all wiring.

 

4.

Faulty solenoid or starter.

4.

Check/replace solenoid or starter.

 

 

 

 

 

 

Loss of power

1.

Cutting too much grass/too fast.

1.

Raise cutting height/reduce speed.

 

2.

Throttle in “CHOKE” position.

2.

Adjust throttle control.

 

3.

Build-up of grass, leaves and trash under mower.

3.

Clean underside of mower housing.

 

4.

Dirty air filter.

4.

Clean/replace air filter.

 

5.

Low oil level/dirty oil.

5.

Check oil level/change oil.

 

6.

Faulty spark plug.

6.

Clean and regap or change spark plug.

 

7.

Dirty fuel filter.

7.

Replace fuel filter.

 

8.

Stale or dirty fuel.

8.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

9.

Water in fuel.

9.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

10.

Spark plug wire loose.

10.

Connect and tighten spark plug wire.

 

11.

Dirty engine air screen/fins.

11.

Clean engine air screen/fins.

 

12.

Dirty/clogged muffler.

12.

Clean/replace muffler.

 

13.

Loose or damaged wiring.

13.

Check all wiring.

 

14.

Carburetor out of adjustment.

14.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

15.

Engine valves out of adjustment.

15.

Contact an authorized service center/department.

 

 

 

 

 

 

Excessive vibration

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Bent blade mandrel.

2.

Replace blade mandrel.

 

3.

Loose/damaged part(s).

3.

Tighten loose part(s). Replace damaged parts.

 

 

 

 

 

 

25

Image 25
Contents Model NO. WET1742STB Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Install Seat See FigCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsLubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine Muffler CleaningSpark Plugs IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigReplacing Battery See Figs To Start Engine with a Weak Battery See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILTroubleshooting Points With attachment clutch Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

191064 specifications

The Weed Eater 191064 is a powerful and efficient tool designed for both residential and commercial lawn care. This gas-powered string trimmer is known for its robust design and user-friendly features, making it a popular choice among gardening enthusiasts and professionals alike.

One of the standout features of the Weed Eater 191064 is its lightweight construction, which significantly reduces operator fatigue during extended use. The ergonomic design ensures a comfortable grip, allowing users to maneuver around gardens, flower beds, and hard-to-reach areas with ease. The trimmer is equipped with a 28cc two-cycle engine that provides ample power for tackling even the most challenging weeds and overgrowth.

In terms of technology, the Weed Eater 191064 utilizes a bump feed system to release cutting line. This user-friendly feature allows you to simply tap the trimmer head on the ground while in operation to release more line as needed, ensuring uninterrupted work without the hassle of constantly stopping to adjust the line. This mechanism not only boosts productivity but also enhances overall efficiency.

The trimmer boasts a dual line cut, meaning it uses two lines simultaneously, allowing for a wider cutting swath. This feature leads to faster trimming times, making it an ideal choice for large yards or commercial landscaping jobs. Moreover, the Weed Eater 191064 is designed to accept a variety of different cutting attachments, giving users the flexibility to switch between trimming, edging, and even brush cutting as needed.

The engine is also designed with fuel efficiency in mind. The Weed Eater 191064 uses a fuel-efficient two-cycle engine that reduces fuel consumption while still delivering high torque power. This translates to lower running costs and, importantly, a reduced environmental impact compared to some competitors.

The ease of maintenance is another significant characteristic of the Weed Eater 191064. With accessible parts and straightforward assembly, users can quickly perform regular upkeep, ensuring the longevity and performance of the trimmer.

Overall, the Weed Eater 191064 is a versatile and user-friendly trimmer that excels in performance, making it a valuable addition to any landscaping toolkit. Whether for a homeowner wanting to maintain their yard or a professional needing reliable equipment, this trimmer delivers on all fronts.