Weed Eater 191064 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 26)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

01536

FIG. 26

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. WET1742STB Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Install Seat See FigCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine IN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig To Adjust Steering Wheel ALIGN- MentTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig Front Wheel TOE-IN/CAMBERTo Remove CABLES, Reverse Order To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points With attachment clutch Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

191064 specifications

The Weed Eater 191064 is a powerful and efficient tool designed for both residential and commercial lawn care. This gas-powered string trimmer is known for its robust design and user-friendly features, making it a popular choice among gardening enthusiasts and professionals alike.

One of the standout features of the Weed Eater 191064 is its lightweight construction, which significantly reduces operator fatigue during extended use. The ergonomic design ensures a comfortable grip, allowing users to maneuver around gardens, flower beds, and hard-to-reach areas with ease. The trimmer is equipped with a 28cc two-cycle engine that provides ample power for tackling even the most challenging weeds and overgrowth.

In terms of technology, the Weed Eater 191064 utilizes a bump feed system to release cutting line. This user-friendly feature allows you to simply tap the trimmer head on the ground while in operation to release more line as needed, ensuring uninterrupted work without the hassle of constantly stopping to adjust the line. This mechanism not only boosts productivity but also enhances overall efficiency.

The trimmer boasts a dual line cut, meaning it uses two lines simultaneously, allowing for a wider cutting swath. This feature leads to faster trimming times, making it an ideal choice for large yards or commercial landscaping jobs. Moreover, the Weed Eater 191064 is designed to accept a variety of different cutting attachments, giving users the flexibility to switch between trimming, edging, and even brush cutting as needed.

The engine is also designed with fuel efficiency in mind. The Weed Eater 191064 uses a fuel-efficient two-cycle engine that reduces fuel consumption while still delivering high torque power. This translates to lower running costs and, importantly, a reduced environmental impact compared to some competitors.

The ease of maintenance is another significant characteristic of the Weed Eater 191064. With accessible parts and straightforward assembly, users can quickly perform regular upkeep, ensuring the longevity and performance of the trimmer.

Overall, the Weed Eater 191064 is a versatile and user-friendly trimmer that excels in performance, making it a valuable addition to any landscaping toolkit. Whether for a homeowner wanting to maintain their yard or a professional needing reliable equipment, this trimmer delivers on all fronts.
Top Page Image Contents