Weed Eater 188313 manual Tractor

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 8)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

TRAILING

MANDREL

EDGE UP BLADE

ASSEMBLY

CENTER

 

HOLE

 

FLAT WASHER

 

LOCK WASHER

 

 

STAR

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 8

TO SHARPEN BLADE (See Fig. 9)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

 

CENTER HOLE

5/8" BOLT

BLADE

 

OR PIN

 

FIG. 9

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model NO. WET2242STC Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine IN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb Interlocks and RelaysTo Replace Fuse To Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WET2242STC SchematicElectrical KEY Part Description Chassis and Enclosures 219 17670508 Screw 5479J Plug Btn Blk Drive Shaft Asm Cross Tapered PMST/20 Steering Assembly Nut Hex Jam Toplock 1/2-20 Unf Engine Gasket Order Parts From Engine Manufacturer Seat Assembly Wheels & Tires DecalsMower Lift 159460 Mower Deck Mandrel Assembly Includes Hous Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation

188313 specifications

The Weed Eater 188313 is a highly regarded string trimmer designed for both homeowners and professionals seeking a reliable tool for maintaining pristine lawns and gardens. Built for ease of use and efficient performance, the 188313 boasts a range of features and technologies that set it apart in the competitive market of outdoor power equipment.

At the heart of the Weed Eater 188313 is its powerful, easy-start engine that provides impressive cutting capabilities without the hassle of traditional pull-start systems. This efficient engine is designed to tackle tough overgrowth while being lightweight enough to reduce user fatigue during extended tasks. The balanced design of the trimmer ensures comfort and stability, allowing users to maneuver with precision.

One of the standout features of the 188313 is its innovative cutting head technology. The trimmer is equipped with a bump feed system, enabling users to easily advance the cutting string with a simple bump on the ground. This feature not only increases productivity but also ensures that the user can maintain an uninterrupted workflow without frequent pauses to reload the string.

The Weed Eater 188313 also incorporates a dual-line cutting system, which effectively doubles the cutting width compared to single-line units. This means that users can cover more ground in less time, making the trimmer ideal for larger properties or extensive landscaping tasks. The dual-line system is designed for durability, enabling it to withstand the rigors of regular trimming without frequent replacements.

Moreover, safety is a priority with the Weed Eater 188313, which features a protective guard that shields the operator from debris while trimming. The ergonomic handle provides a firm grip, enhancing control and reducing the risk of accidents during operation.

The lightweight materials used in constructing the 188313 ensure that it is easy to transport and maneuver, appealing to those who require a portable solution for their lawn care needs. Its compatibility with various attachments also allows for versatility, enabling users to switch between tasks, such as edging and brushing, effortlessly.

In summary, the Weed Eater 188313 is a robust string trimmer that combines power, efficiency, and user-friendly features. With its advanced cutting head technology, lightweight design, and commitment to safety, it stands as an excellent choice for anyone looking to maintain their outdoor spaces effectively. Whether you are an occasional gardener or a dedicated professional, the Weed Eater 188313 provides the performance and reliability required for a well-manicured lawn.
Top Page Image Contents