Weed Eater 188313 manual To Check and Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 20

SERVICE AND ADJUSTMENTS

IDLER PULLEYS

MANDREL PULLEYS

FIG. 18

TO CHECK AND ADJUST BRAKE (See Fig. 19)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

•Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

•Place gear shift lever in neutral (N) position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

•Depress clutch/brake pedal all the way down and en- gage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-1/2", loosen jam nut and turn nut “A” until distance becomes 1-1/2". Retighten jam nut against nut “A”.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

1-1/2"

NUT “A”

JAM NUT

OPERATING ARM

FIG. 19

TO REPLACE MOTION DRIVE BELT (See Fig. 20)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keep- ers.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down between transaxle belt keepers and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model NO. WET2242STC Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine Mowing Tips To Start Engine See FigMaintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Check and Adjust Brake See Fig To Adjust BrakeTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Replace Fuse To Replace Headlight BulbInterlocks and Relays To Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control Storage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WET2242STCElectrical KEY Part Description Chassis and Enclosures 219 17670508 Screw 5479J Plug Btn Blk Drive Shaft Asm Cross Tapered PMST/20 Steering Assembly Nut Hex Jam Toplock 1/2-20 Unf Engine Gasket Order Parts From Engine Manufacturer Seat Assembly Decals Wheels & TiresMower Lift 159460 Mower Deck Mandrel Assembly Includes Hous Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation

188313 specifications

The Weed Eater 188313 is a highly regarded string trimmer designed for both homeowners and professionals seeking a reliable tool for maintaining pristine lawns and gardens. Built for ease of use and efficient performance, the 188313 boasts a range of features and technologies that set it apart in the competitive market of outdoor power equipment.

At the heart of the Weed Eater 188313 is its powerful, easy-start engine that provides impressive cutting capabilities without the hassle of traditional pull-start systems. This efficient engine is designed to tackle tough overgrowth while being lightweight enough to reduce user fatigue during extended tasks. The balanced design of the trimmer ensures comfort and stability, allowing users to maneuver with precision.

One of the standout features of the 188313 is its innovative cutting head technology. The trimmer is equipped with a bump feed system, enabling users to easily advance the cutting string with a simple bump on the ground. This feature not only increases productivity but also ensures that the user can maintain an uninterrupted workflow without frequent pauses to reload the string.

The Weed Eater 188313 also incorporates a dual-line cutting system, which effectively doubles the cutting width compared to single-line units. This means that users can cover more ground in less time, making the trimmer ideal for larger properties or extensive landscaping tasks. The dual-line system is designed for durability, enabling it to withstand the rigors of regular trimming without frequent replacements.

Moreover, safety is a priority with the Weed Eater 188313, which features a protective guard that shields the operator from debris while trimming. The ergonomic handle provides a firm grip, enhancing control and reducing the risk of accidents during operation.

The lightweight materials used in constructing the 188313 ensure that it is easy to transport and maneuver, appealing to those who require a portable solution for their lawn care needs. Its compatibility with various attachments also allows for versatility, enabling users to switch between tasks, such as edging and brushing, effortlessly.

In summary, the Weed Eater 188313 is a robust string trimmer that combines power, efficiency, and user-friendly features. With its advanced cutting head technology, lightweight design, and commitment to safety, it stands as an excellent choice for anyone looking to maintain their outdoor spaces effectively. Whether you are an occasional gardener or a dedicated professional, the Weed Eater 188313 provides the performance and reliability required for a well-manicured lawn.
Top Page Image Contents