Weed Eater 188313 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

7/16" wrenches

Utility knife

(2)

3/4" wrench

Tire pressure gauge

Pliers

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 1/2 hex nut and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKIDTHAT MAY PUNCTURETIRESWHERETRACTOR IS TO ROLL OFF SKID.

 

INSERT

 

1/2 HEX NUT

 

LARGE FLAT

 

WASHER

STEERING

 

WHEEL

STEERING

 

 

BOOT

 

TABS

ADAPTER

 

 

EXTENSION SHAFT

 

1/4 HEX BOLT

1/4 LOCKNUT

 

LOWER

 

STEERING

 

SHAFT

 

 

TAB

 

SLOTS

FIG. 1

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model NO. WET2242STC Safety Rules Safety Rules Table of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine Mowing Tips To Start Engine See FigGeneral Recommendations MaintenanceLubrication Chart Before Each USETractor Engine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment To Remove Wheel for Repairs See FigTo Replace Headlight Bulb Interlocks and RelaysTo Replace Fuse To Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor Fuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WET2242STCElectrical KEY Part Description Chassis and Enclosures 219 17670508 Screw 5479J Plug Btn Blk Drive Shaft Asm Cross Tapered PMST/20 Steering Assembly Nut Hex Jam Toplock 1/2-20 Unf Engine Gasket Order Parts From Engine Manufacturer Seat Assembly Decals Wheels & TiresMower Lift 159460 Mower Deck Mandrel Assembly Includes Hous Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation

188313 specifications

The Weed Eater 188313 is a highly regarded string trimmer designed for both homeowners and professionals seeking a reliable tool for maintaining pristine lawns and gardens. Built for ease of use and efficient performance, the 188313 boasts a range of features and technologies that set it apart in the competitive market of outdoor power equipment.

At the heart of the Weed Eater 188313 is its powerful, easy-start engine that provides impressive cutting capabilities without the hassle of traditional pull-start systems. This efficient engine is designed to tackle tough overgrowth while being lightweight enough to reduce user fatigue during extended tasks. The balanced design of the trimmer ensures comfort and stability, allowing users to maneuver with precision.

One of the standout features of the 188313 is its innovative cutting head technology. The trimmer is equipped with a bump feed system, enabling users to easily advance the cutting string with a simple bump on the ground. This feature not only increases productivity but also ensures that the user can maintain an uninterrupted workflow without frequent pauses to reload the string.

The Weed Eater 188313 also incorporates a dual-line cutting system, which effectively doubles the cutting width compared to single-line units. This means that users can cover more ground in less time, making the trimmer ideal for larger properties or extensive landscaping tasks. The dual-line system is designed for durability, enabling it to withstand the rigors of regular trimming without frequent replacements.

Moreover, safety is a priority with the Weed Eater 188313, which features a protective guard that shields the operator from debris while trimming. The ergonomic handle provides a firm grip, enhancing control and reducing the risk of accidents during operation.

The lightweight materials used in constructing the 188313 ensure that it is easy to transport and maneuver, appealing to those who require a portable solution for their lawn care needs. Its compatibility with various attachments also allows for versatility, enabling users to switch between tasks, such as edging and brushing, effortlessly.

In summary, the Weed Eater 188313 is a robust string trimmer that combines power, efficiency, and user-friendly features. With its advanced cutting head technology, lightweight design, and commitment to safety, it stands as an excellent choice for anyone looking to maintain their outdoor spaces effectively. Whether you are an occasional gardener or a dedicated professional, the Weed Eater 188313 provides the performance and reliability required for a well-manicured lawn.
Top Page Image Contents