Weed Eater HD13538 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 19

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place gearshift lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 13)

Mower will be easier to remove from the right side of trac- tor.

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Remove small retainer spring, and remove clutch spring off pulley bolt.

•Remove large retainer spring, slide collar off and push housing guide out of bracket.

•Disconnect anti-swaybar from chassis bracket by re- moving retainer spring.

•Disconnect suspension arms from rear deck brackets by removing retainer springs.

•Disconnect front links from deck by removing retainer springs.

•Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHERTHANTHE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINKS AND HOOK THE CLUTCH SPRING INTO SQUARE HOLE IN FRAME.

TO INSTALL MOWER (See Fig. 13)

•Raise attachment lift lever to its highest position.

•Slide mower under tractor with defl ector shield to right side of tractor.

•Lower lift lever to its lowest position.

•Connect front links to mower deck and secure with retainer springs..

•Connect suspension arms to rear deck brackets and secure with retainer springs.

•Connect anti-swaybar to chassis bracket and secure with retainer spring.

•Push clutch cable housing guide into bracket, slide col- lar onto guide and secure with large retainer spring.

•Place fl at washer and clutch spring on idler pulley bolt and secure with small retainer spring.

•Make sure belt is inside the belt keeper at the idler and on both sides of the wire belt keeper as shown.

•Install belt onto engine pulley.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

SMALL RETAINER SPRING

 

 

FLAT WASHER

 

WIRE BELT KEEPER

 

 

CLUTCH SPRING

 

 

SUSPENSION ARMS

 

 

 

BELT KEEPER

 

 

 

 

 

SQUARE HOLE

RETAINER SPRING

 

 

ENGINE PULLEY

ANTI-SWAY BAR

 

 

 

 

FRONT LINK

COLLAR

 

 

 

 

 

HOUSING GUIDE

 

 

RETAINER SPRINGS

 

 

 

(BOTH SIDES)

LARGE

BRACKET

02845

 

 

DEFLECTOR SHIELD

RETAINER

CLUTCH SPRING

SPRING

 

FIG. 13

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Always Wear EYE Protection During Operation HD13538II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport Reverse Operation System ROSTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips General Recommendations MaintenanceBlade Removal See Fig TractorTo Sharpen Blade See Fig Transaxle Cooling BatteryEngine BeltsMuffler CleaningClean AIR Screen AIR FilterTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

HD13538 specifications

The Weed Eater HD13538 is a robust and reliable string trimmer designed for efficient lawn care and maintenance. With its impressive features and advanced technologies, this power tool stands out among its competitors, making it an essential item for homeowners and gardening enthusiasts alike.

One of the key features of the HD13538 is its powerful 38cc engine. This engine provides ample power to tackle thick weeds, grass, and underbrush with ease. The robust performance of this trimmer makes it suitable for both small and larger yards, ensuring that users can achieve a well-manicured appearance for their outdoor spaces without the hassle of underpowered equipment.

The weed eater also boasts a lightweight design, weighing in at just around 10 pounds. This is particularly advantageous for extended use, as it minimizes fatigue and allows users to maneuver the trimmer easily. The ergonomically designed handle adds to the overall comfort, making it user-friendly while providing optimal control during operation.

A standout feature of the Weed Eater HD13538 is its innovative 2-in-1 capability, which allows users to easily switch between trimming and edging tasks. The adjustable shaft length offers additional convenience, accommodating users of various heights and ensuring that every job can be completed with precision.

Equipped with a bump feed mechanism, the HD13538 allows for quick line advancement, ensuring that users can keep working without interruptions. Simply tap the trimmer head on the ground, and the line automatically feeds out, providing continuous cutting power and saving time during yard work.

The weed trimmer also features a durable construction designed for longevity. Additionally, the trimmer head is designed to accept various line thicknesses, giving users the flexibility to choose the best option for their specific lawn care needs.

In terms of maintenance, the Weed Eater HD13538 is straightforward. Its simple start system reduces the frustration often associated with starting gas-powered equipment, while the accessible air filter and spark plug make periodic maintenance tasks a breeze.

Overall, the Weed Eater HD13538 offers a well-rounded combination of power, ease of use, and durability. Its advanced features and technologies cater to the needs of both casual gardeners and diligent landscapers, making it a top choice for anyone looking to maintain a tidy outdoor space.
Top Page Image Contents