Weed Eater HD13538 manual To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly infl ated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinfl ated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 14 and 15)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 14

SUSPENSION ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 15

FRONT-TO-BACK ADJUSTMENT (See Figs. 16 and 17)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.The two front links must remain equal in length.

•When distance “D”is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

“D”

“D”

FIG. 16

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “F”

NUT “E”

TRUNNION

FRONT LINKS

FIG. 17

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 18)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Work new belt around both mandrel pulleys and idler pulleys.

•Install new belt into engine pulley groove.

•Make sure belt is inside the belt keeper at the idler and on both sides of the wire belt keeper as shown.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents HD13538 Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Maintenance General RecommendationsTo Sharpen Blade See Fig TractorBlade Removal See Fig Battery EngineBelts Transaxle CoolingCleaning Clean AIR ScreenAIR Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Check and Adjust Brake See Fig To Adjust BrakeTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

HD13538 specifications

The Weed Eater HD13538 is a robust and reliable string trimmer designed for efficient lawn care and maintenance. With its impressive features and advanced technologies, this power tool stands out among its competitors, making it an essential item for homeowners and gardening enthusiasts alike.

One of the key features of the HD13538 is its powerful 38cc engine. This engine provides ample power to tackle thick weeds, grass, and underbrush with ease. The robust performance of this trimmer makes it suitable for both small and larger yards, ensuring that users can achieve a well-manicured appearance for their outdoor spaces without the hassle of underpowered equipment.

The weed eater also boasts a lightweight design, weighing in at just around 10 pounds. This is particularly advantageous for extended use, as it minimizes fatigue and allows users to maneuver the trimmer easily. The ergonomically designed handle adds to the overall comfort, making it user-friendly while providing optimal control during operation.

A standout feature of the Weed Eater HD13538 is its innovative 2-in-1 capability, which allows users to easily switch between trimming and edging tasks. The adjustable shaft length offers additional convenience, accommodating users of various heights and ensuring that every job can be completed with precision.

Equipped with a bump feed mechanism, the HD13538 allows for quick line advancement, ensuring that users can keep working without interruptions. Simply tap the trimmer head on the ground, and the line automatically feeds out, providing continuous cutting power and saving time during yard work.

The weed trimmer also features a durable construction designed for longevity. Additionally, the trimmer head is designed to accept various line thicknesses, giving users the flexibility to choose the best option for their specific lawn care needs.

In terms of maintenance, the Weed Eater HD13538 is straightforward. Its simple start system reduces the frustration often associated with starting gas-powered equipment, while the accessible air filter and spark plug make periodic maintenance tasks a breeze.

Overall, the Weed Eater HD13538 offers a well-rounded combination of power, ease of use, and durability. Its advanced features and technologies cater to the needs of both casual gardeners and diligent landscapers, making it a top choice for anyone looking to maintain a tidy outdoor space.
Top Page Image Contents