Weed Eater 171883 manual Mowing Tips, To Start Engine See Fig

Page 13

OPERATION

TO START ENGINE (See Fig. 5)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place gear shift lever in neutral (N) position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depending on the tempera- ture.

•The attachments can also be used during the engine warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

MOWING TIPS

•Tire chains cannot be used when the mower housing is attached to tractor.

•Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trimming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 7 ).

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mowing to assure better mowing performance and proper dis- charge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting perfor- mance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

FIG. 7

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model NO. WE12538G Safe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Customer Responsibilities Product SpecificationsSteering Wheel Seat Unassembled PartsKeys Slope SheetTools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor To USE Throttle Control see FIG HOW to USE Your TractorTo Operate on Hills Before Starting the EngineTo Transport Towing Carts and Other ATTACH- MentsTo Start Engine See Fig Mowing TipsCustomer Responsibilities ¿ Lubrication ChartGeneral Recommendations Before Each USEBrake Operation TractorTires Operator Presence SystemEngine BatteryBelts Transaxle CoolingTo Service PRE-CLEANER Clean AIR Screen See FigTo Service Cartridge Engine Cooling Fins See FigMuffler CleaningSpark Plugs IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Remove Hood and Grill Assembly See Fig Replacing Battery SeeTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor See Fig To Adjust Throttle Control Cable See FigPreliminary Setting Final SettingOther StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number WE12538G SchematicElectrical KEY Part NO. NO.DESCRIPTION Chassis KEY Part Description Drive Transaxle Steering KEY Engine 140310 Control Th/ch Flag Seat Wheels & Tires DecalsLSB42 LBD48Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Service Sighting Guide Suggested Guide for Sighting Slopes for Safe Operation

171883 specifications

The Weed Eater 171883 is a premier choice for homeowners and gardening enthusiasts seeking an efficient, reliable, and user-friendly string trimmer. This model is specifically designed to simplify yard maintenance, making it an essential tool for tackling overgrown grasses, weeds, and even light brush.

One of the standout features of the Weed Eater 171883 is its lightweight design. Weighing in at a manageable level, this trimmer is easy to handle, allowing users to maneuver effortlessly around garden beds, fences, and other obstacles. The balanced weight distribution means less fatigue during extended use, making it a practical option for larger yards.

The 171883 model incorporates a powerful motor that delivers high performance, ensuring effective cutting power. With its notable RPM (revolutions per minute), users can expect fast and efficient trimming, significantly reducing the time spent on yard work. This makes it an ideal solution for busy homeowners who require a quick yet effective gardening tool.

Another key feature is the innovative line feed technology. This model utilizes a bump feed system, which allows the user to release more cutting line simply by tapping the trimmer head on the ground. This easy-to-use mechanism ensures that you always have the optimal length of line for the job without the need for manual adjustments, allowing for a more efficient workflow.

The Weed Eater 171883 also boasts adjustable handle positions, providing customizable comfort and control. Users can easily modify the height of the handle for a more ergonomic grip, reducing strain on the wrists and back during prolonged use.

Finally, the trimmer is equipped with a durable and robust cutting head that can withstand the rigors of outdoor use. Its reinforced construction means it can handle tough vegetation with ease while offering quick and straightforward line changes.

In summary, the Weed Eater 171883 combines lightweight design, powerful performance, user-friendly features, and durability. It is an essential tool for anyone looking to maintain their yard efficiently and effectively, making outdoor chores less of a burden and more of an enjoyable experience. With this trimmer, keeping your lawn looking pristine has never been easier.
Top Page Image Contents