Weed Eater 171883 To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 16 and 17)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

BOTTOM EDGE

OF MOWER

OF MOWER

TO GROUND

TO GROUND

“A”

“A”

 

GROUND LINE

FIG. 16

SUSPENSION ARM

LIFT LINK

ADJUSTMENT

NUT

FIG. 17

FRONT-TO-BACK ADJUSTMENT (See Figs. 18 and 19)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 18

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 19

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 20)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

• Before making any necessary adjustments, check that both front links are equal in length. Both links should be approximately 10-3/8".

• If links are not equal in length, adjust one link to same length as other link.

• To lower front of mower loosen nut “E” on both front links an equal number of turns.

20

MANDREL

IDLER PULLEYS

PULLEY

 

MANDREL

PULLEY

FIG. 20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model NO. WE12538G Safety Rules Safe Operation Practices for Ride-On MowersTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Parts Steering Wheel SeatKeys Slope SheetAssembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To USE Throttle Control see FIGBefore Starting the Engine To Operate on HillsTo Transport Towing Carts and Other ATTACH- MentsMowing Tips To Start Engine See Fig¿ Lubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USETractor Brake OperationTires Operator Presence SystemBattery EngineBelts Transaxle CoolingClean AIR Screen See Fig To Service PRE-CLEANERTo Service Cartridge Engine Cooling Fins See FigCleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERReplacing Battery See To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust Carburetor See FigPreliminary Setting Final SettingStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WE12538GElectrical KEY Part NO. NO.DESCRIPTION Chassis KEY Part Description Drive Transaxle Steering KEY Engine 140310 Control Th/ch Flag Seat Decals Wheels & TiresLSB42 LBD48Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Service Suggested Guide for Sighting Slopes for Safe Operation Sighting Guide

171883 specifications

The Weed Eater 171883 is a premier choice for homeowners and gardening enthusiasts seeking an efficient, reliable, and user-friendly string trimmer. This model is specifically designed to simplify yard maintenance, making it an essential tool for tackling overgrown grasses, weeds, and even light brush.

One of the standout features of the Weed Eater 171883 is its lightweight design. Weighing in at a manageable level, this trimmer is easy to handle, allowing users to maneuver effortlessly around garden beds, fences, and other obstacles. The balanced weight distribution means less fatigue during extended use, making it a practical option for larger yards.

The 171883 model incorporates a powerful motor that delivers high performance, ensuring effective cutting power. With its notable RPM (revolutions per minute), users can expect fast and efficient trimming, significantly reducing the time spent on yard work. This makes it an ideal solution for busy homeowners who require a quick yet effective gardening tool.

Another key feature is the innovative line feed technology. This model utilizes a bump feed system, which allows the user to release more cutting line simply by tapping the trimmer head on the ground. This easy-to-use mechanism ensures that you always have the optimal length of line for the job without the need for manual adjustments, allowing for a more efficient workflow.

The Weed Eater 171883 also boasts adjustable handle positions, providing customizable comfort and control. Users can easily modify the height of the handle for a more ergonomic grip, reducing strain on the wrists and back during prolonged use.

Finally, the trimmer is equipped with a durable and robust cutting head that can withstand the rigors of outdoor use. Its reinforced construction means it can handle tough vegetation with ease while offering quick and straightforward line changes.

In summary, the Weed Eater 171883 combines lightweight design, powerful performance, user-friendly features, and durability. It is an essential tool for anyone looking to maintain their yard efficiently and effectively, making outdoor chores less of a burden and more of an enjoyable experience. With this trimmer, keeping your lawn looking pristine has never been easier.
Top Page Image Contents