Weed Eater 176840 Before Starting the Engine, To Operate on Hills, To Transport, ADD Gasoline

Page 12

OPERATION

TO OPERATE MOWER (See Fig. 6)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT LIFT

LEVER HIGH POSITION

LOW

POSITION

ATTACHMENT CLUTCH LEVER "DISENGAGED" POSITION

DEFLECTOR

SHIELD

FIG. 6

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

• Choose the slowest speed before starting up or down hills.

• Avoid stopping or changing speed on hills.

• If slowing is necessary, move throttle control lever to slower position.

• If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

• Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

• To restart movement, slowly release parking brake and clutch/brake pedal.

• Make all turns slowly.

12

TO TRANSPORT

•Raise attachment lift to highest position with attachment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 11)

•The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Customer Responsibilities section of this manual).

•To change engine oil, see the Customer Responsibilities section in this manual.

ADD GASOLINE

•Fill fuel tank. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

WARNING: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

CAUTION: Fill to bottom of gas tank filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model NO. WE12538H Safety Rules Safe Operation Practices for Ride-On MowersTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Parts Steering Wheel SeatKeys Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidHOW to SET UP Your Tractor Check Battery See FigInstall Seat See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To USE Throttle Control see FIGBefore Starting the Engine To Operate on HillsTo Transport Towing Carts and Other ATTACH- MentsMowing Tips To Start Engine See Fig¿ Lubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USETractor Brake OperationTires Operator Presence SystemBattery EngineBelts Transaxle CoolingClean AIR Screen To Service PRE-CLEANERTo Service Cartridge Engine Cooling Fins See FigCleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERReplacing Battery See Figs To Replace Headlight BulbInterlocks and Relays To Replace FuseTo Remove Hood and Grill Assembly See Fig To Adjust CarburetorTo Adjust Throttle Control Cable See Fig EngineStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WE12538HElectrical 2122175158 175566175141 Chassis KEY Part Description Drive 112 113 170 116 202 150 151 145 2675174973 173898Steering 140044X428 154427 Axle AsmOptional Equipment 170551 Control Th/ch Flag 14831571070512 Seat 174894Decals Wheels & Tires176840 176841Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Securing Warranty Service No Dealer WarrantyProducts Warranted Products And Items Not WarrantedOnly Ride UP and Down Hill SightingNot Across Hill Guide

176840 specifications

The Weed Eater 176840 is an exceptional landscaping tool designed to make yard maintenance efficient and effortless. This impressive model stands out in the market for its user-friendly features, advanced technologies, and robust performance, making it a top choice for both homeowners and professional landscapers.

One of the most notable features of the Weed Eater 176840 is its lightweight design. Weighing in at just a few pounds, this trimmer allows users to maneuver it easily around their gardens, avoiding the fatigue often associated with heavier models. The ergonomic handle contributes to ease of use, making it comfortable for extended periods of operation.

The Weed Eater 176840 is equipped with a powerful 2-cycle engine, delivering high speed and performance for tackling various types of vegetation. This engine ensures efficient cutting power, allowing users to trim grass and weeds with precision. The air-filter technology incorporated into the engine enhances performance, enabling optimal air flow while reducing emissions, thus making it environmentally friendly.

Another standout feature is the innovative bump head design, which simplifies line advancement. Users can quickly release more cutting line by tapping the head on the ground, eliminating the need to stop and manually feed the trimmer line. This feature greatly enhances productivity, allowing users to stay focused on their landscaping tasks.

The 176840 model also offers adjustable cutting widths, which provides versatility for different trimming needs. Users can switch between wider and narrower cutting paths according to the requirements of their yard, whether it be edging sidewalks or tackling overgrown areas.

Moreover, the Weed Eater 176840 is designed with durability in mind. Constructed from high-quality materials, it can withstand the rigors of outdoor use while resisting wear and tear. This reliability ensures that users can depend on their trimmer season after season.

Additionally, easy maintenance features, such as accessible air filters and spark plugs, allow for straightforward upkeep, enhancing the longevity of the trimmer. The model is also compatible with various accessories, enabling users to transform their trimmer into a multi-functional tool.

In summary, the Weed Eater 176840 is a strong contender in the world of garden equipment, offering a combination of powerful performance, innovative technologies, and user-friendly characteristics. Whether for residential use or professional landscaping, this trimmer provides everything needed for effective yard management. It represents the ideal solution for maintaining a beautiful and well-groomed outdoor space.
Top Page Image Contents