Weed Eater 176840 owner manual Off

Page 26

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

 

 

 

 

Engine continues to run

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not

when operator leaves

 

 

 

corrected, contact an authorized service center/

seat with attachment

 

 

 

department.

clutch engaged

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Mower deck not level.

2.

Level mower deck.

 

3.

Buildup of grass, leaves, and trash under mower.

3.

Clean underside of mower housing.

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

5.

Clogged mower deck vent holes from buildup of

5.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Mower blades will not

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

Poor grass discharge

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

4.

Mower deck not level.

4.

Level mower deck.

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

6.

Worn, bent or loose blade.

6.

Replace/sharpen blade. Tighten blade bolt.

 

7.

Buildup of grass, leaves and trash under mower.

7.

Clean underside of mower housing.

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

10.

Improper blades used.

10.

Replace with blades listed in this manual.

 

11.

Clogged mower deck vent holes from buildup of

11.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Headlight(s) not working

1.

Switch is “OFF”.

1.

Turn switch “ON”.

(if so equipped)

2.

Bulb(s) burned out.

2.

Replace bulb(s).

 

3.

Faulty light switch.

3.

Check/replace light switch.

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

Battery will not charge

1.

Bad battery cell(s).

1.

Replace battery.

 

2.

Poor cable connections.

2.

Check/clean all connections.

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

Engine “backfires”

1.

Engine throttle control not set at “SLOW”

1.

Move throttle control to “SLOW” position and allow

when turning engine

 

position for 30 seconds before stopping engine.

 

to idle for 30 seconds before stopping engine.

“OFF”

 

 

 

 

 

 

 

 

 

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Model NO. WE12538H Safety Rules Safe Operation Practices for Ride-On MowersTable of Contents Product Specifications Customer ResponsibilitiesKeys Unassembled PartsSteering Wheel Seat To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To USE Throttle Control see FIGTo Transport Before Starting the EngineTo Operate on Hills Towing Carts and Other ATTACH- MentsMowing Tips To Start Engine See FigGeneral Recommendations ¿ Lubrication ChartCustomer Responsibilities Before Each USETires TractorBrake Operation Operator Presence SystemBelts BatteryEngine Transaxle CoolingTo Service Cartridge Clean AIR ScreenTo Service PRE-CLEANER Engine Cooling Fins See FigSpark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERInterlocks and Relays Replacing Battery See FigsTo Replace Headlight Bulb To Replace FuseTo Adjust Throttle Control Cable See Fig To Remove Hood and Grill Assembly See FigTo Adjust Carburetor EngineFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WE12538HElectrical 2122175141 175158175566 Chassis KEY Part Description Drive 112 113 170 116 202 150 151 145 2675174973 173898Steering 140044X428 154427 Axle AsmOptional Equipment 71070512 170551 Control Th/ch Flag148315 Seat 174894176840 DecalsWheels & Tires 176841Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Products Warranted Securing Warranty ServiceNo Dealer Warranty Products And Items Not WarrantedNot Across Hill Only Ride UP and Down HillSighting Guide

176840 specifications

The Weed Eater 176840 is an exceptional landscaping tool designed to make yard maintenance efficient and effortless. This impressive model stands out in the market for its user-friendly features, advanced technologies, and robust performance, making it a top choice for both homeowners and professional landscapers.

One of the most notable features of the Weed Eater 176840 is its lightweight design. Weighing in at just a few pounds, this trimmer allows users to maneuver it easily around their gardens, avoiding the fatigue often associated with heavier models. The ergonomic handle contributes to ease of use, making it comfortable for extended periods of operation.

The Weed Eater 176840 is equipped with a powerful 2-cycle engine, delivering high speed and performance for tackling various types of vegetation. This engine ensures efficient cutting power, allowing users to trim grass and weeds with precision. The air-filter technology incorporated into the engine enhances performance, enabling optimal air flow while reducing emissions, thus making it environmentally friendly.

Another standout feature is the innovative bump head design, which simplifies line advancement. Users can quickly release more cutting line by tapping the head on the ground, eliminating the need to stop and manually feed the trimmer line. This feature greatly enhances productivity, allowing users to stay focused on their landscaping tasks.

The 176840 model also offers adjustable cutting widths, which provides versatility for different trimming needs. Users can switch between wider and narrower cutting paths according to the requirements of their yard, whether it be edging sidewalks or tackling overgrown areas.

Moreover, the Weed Eater 176840 is designed with durability in mind. Constructed from high-quality materials, it can withstand the rigors of outdoor use while resisting wear and tear. This reliability ensures that users can depend on their trimmer season after season.

Additionally, easy maintenance features, such as accessible air filters and spark plugs, allow for straightforward upkeep, enhancing the longevity of the trimmer. The model is also compatible with various accessories, enabling users to transform their trimmer into a multi-functional tool.

In summary, the Weed Eater 176840 is a strong contender in the world of garden equipment, offering a combination of powerful performance, innovative technologies, and user-friendly characteristics. Whether for residential use or professional landscaping, this trimmer provides everything needed for effective yard management. It represents the ideal solution for maintaining a beautiful and well-groomed outdoor space.
Top Page Image Contents