Weed Eater 177019 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

KEPS NUT

 

HEX

 

BOLT

POSITIVE

 

(RED)

NEGATIVE

CABLE

(BLACK)

 

 

CABLE

FIG. 28

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 29)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 29

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 30)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that hole in throttle lever and hole in plate line up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

 

IDLE SPEED

PLATE

SCREW

 

 

THROTTLE CABLE

 

CLAMP

 

SCREW

 

HOLE “A”

THROTTLE

 

LEVER

FAST

FIG. 30

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. S165H42A Safe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Customer Responsibilities Product SpecificationsSlope Sheet Unassembled PartsSteering Wheel Seat KeyTo Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorLower seat into operating position and sit on seat Install Seat See FigCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Before Each USE ¿ Lubrication ChartCustomer Responsibilities General RecommendationsTractor Engine Spark Plugs CleaningAIR Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Level Mower Housing To Install Mower See FigBelt Removal To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove Wheel for Repairs See FigTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number S165H42A SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly KEY Part NO. NO.DESCRIPTION Engine 170551 Control Throt/Ch Seat Assembly Wheels & Tires DecalsMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Repair Parts Service Notes Limited Warranty For Limited WarrantiesOnly Ride UP and Down Hill Suggested Guide for Sighting Slopes for Safe Operation

177019 specifications

The Weed Eater 177019 is a powerful and versatile string trimmer designed for homeowners and landscape enthusiasts alike. With its ease of use and efficient performance, it has become a popular choice for those looking to maintain neat and tidy lawns, gardens, and outdoor spaces.

One of the standout features of the Weed Eater 177019 is its 17-inch cutting width. This wide cutting path allows users to tackle larger areas in less time, making it ideal for properties of varying sizes. The trimmer is equipped with a reliable and robust 25cc 2-cycle engine, providing enough power to handle tough weeds and overgrown grass. The lightweight design, weighing only 10.3 pounds, offers excellent maneuverability, reducing arm fatigue during extended use.

The Weed Eater 177019 features an adjustable telescoping shaft, allowing users to customize the length according to their height and comfort. This ergonomic design enhances user experience, making it suitable for people of all sizes. The soft-grip handle provides additional comfort and control, enabling users to maintain precision while trimming around flower beds and garden borders.

Another impressive characteristic of this trimmer is its automatic line advancement system. This technology ensures that the trimmer line is advanced smoothly and easily, eliminating the hassle of manual adjustments. Users simply tap the head of the trimmer on the ground while in use to release more line, allowing for continuous cutting without interruptions.

The Weed Eater 177019 also incorporates a dual-line system that effectively increases cutting efficiency. This feature allows for a cleaner and more accurate cut, reducing the risk of damaging surrounding plants and structures. The easy-loading spool further simplifies maintenance, enabling users to quickly replace the trimmer line without hassle.

For added convenience, the Weed Eater 177019 is designed for easy starting. Its spring-assisted starter reduces pull resistance, making it simpler for users to get the trimmer up and running. This user-friendly design is a significant advantage, especially for those who may be less experienced with power tools.

In summary, the Weed Eater 177019 is an efficient string trimmer packed with features that promote ease of use and effective lawn care. With its powerful engine, adjustable design, automatic line advancement, and user-friendly operation, it proves to be a reliable choice for anyone looking to keep their outdoor spaces well-groomed. Its combination of performance and comfort makes it a valuable addition to any homeowner's tool collection.
Top Page Image Contents