Weed Eater 177019 manual Transaxle Motion Control Lever Neutral Adjustment See Fig

Page 21

SERVICE AND ADJUSTMENTS

•If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary. Contact your nearest au- thorized service center/department.

WITH PARKING BRAKE

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 24)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•

Loosen adjustment bolt in front of the right rear wheel,

 

and lightly tighten.

•

Start engine and move motion control lever until tractor

 

does not move forward or backward.

“ENGAGED”

NUT “A”

1-9/16"

JAM NUT

OPERATING

ARM

•

Hold motion control lever in that position and turn engine

 

off.

•

While holding motion control lever in place, loosen the

 

adjustment bolt.

•

Move motion control lever to the neutral (N) (lock gate)

 

position.

•

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUSTMENT IS NECESSARY CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/DEPARTMENT

FIG. 22

TO REPLACE MOTION DRIVE BELT (See Fig. 23)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

•Remove mower (See “TO REMOVE MOWER” in this section of this manual.)

•Remove belt from stationary idler and clutching idler.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

•Pull belt toward front of tractor and remove downward from around engine pulley.

•Install new belt by reversing above procedure.

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEY

FIG. 23

position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satisfied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

 

 

ADJUSTMENT

 

BOLT

FIG. 24

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMIS- SION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model NO. S165H42A Safe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Customer Responsibilities Product SpecificationsSteering Wheel Seat Unassembled PartsKey Slope SheetTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonLower seat into operating position and sit on seat Install Seat See FigCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Customer Responsibilities ¿ Lubrication ChartGeneral Recommendations Before Each USETractor Engine AIR Filter CleaningMuffler Spark PlugsTo Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Installation To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransmission REMOVAL/REPLACEMENT Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigReplacing Battery See Figs To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Replace Headlight Bulb To Adjust CarburetorInterlocks and Relays To Replace FuseOther StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number S165H42A SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly KEY Part NO. NO.DESCRIPTION Engine 170551 Control Throt/Ch Seat Assembly Wheels & Tires DecalsMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Repair Parts Service Notes Limited Warranty For Limited WarrantiesOnly Ride UP and Down Hill Suggested Guide for Sighting Slopes for Safe Operation

177019 specifications

The Weed Eater 177019 is a powerful and versatile string trimmer designed for homeowners and landscape enthusiasts alike. With its ease of use and efficient performance, it has become a popular choice for those looking to maintain neat and tidy lawns, gardens, and outdoor spaces.

One of the standout features of the Weed Eater 177019 is its 17-inch cutting width. This wide cutting path allows users to tackle larger areas in less time, making it ideal for properties of varying sizes. The trimmer is equipped with a reliable and robust 25cc 2-cycle engine, providing enough power to handle tough weeds and overgrown grass. The lightweight design, weighing only 10.3 pounds, offers excellent maneuverability, reducing arm fatigue during extended use.

The Weed Eater 177019 features an adjustable telescoping shaft, allowing users to customize the length according to their height and comfort. This ergonomic design enhances user experience, making it suitable for people of all sizes. The soft-grip handle provides additional comfort and control, enabling users to maintain precision while trimming around flower beds and garden borders.

Another impressive characteristic of this trimmer is its automatic line advancement system. This technology ensures that the trimmer line is advanced smoothly and easily, eliminating the hassle of manual adjustments. Users simply tap the head of the trimmer on the ground while in use to release more line, allowing for continuous cutting without interruptions.

The Weed Eater 177019 also incorporates a dual-line system that effectively increases cutting efficiency. This feature allows for a cleaner and more accurate cut, reducing the risk of damaging surrounding plants and structures. The easy-loading spool further simplifies maintenance, enabling users to quickly replace the trimmer line without hassle.

For added convenience, the Weed Eater 177019 is designed for easy starting. Its spring-assisted starter reduces pull resistance, making it simpler for users to get the trimmer up and running. This user-friendly design is a significant advantage, especially for those who may be less experienced with power tools.

In summary, the Weed Eater 177019 is an efficient string trimmer packed with features that promote ease of use and effective lawn care. With its powerful engine, adjustable design, automatic line advancement, and user-friendly operation, it proves to be a reliable choice for anyone looking to keep their outdoor spaces well-groomed. Its combination of performance and comfort makes it a valuable addition to any homeowner's tool collection.
Top Page Image Contents