Weed Eater 177019 manual Off

Page 26

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

Engine continues to run

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not

when operator leaves

 

 

 

corrected, contact an authorized service center/

seat with attachment

 

 

 

department.

clutch engaged

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Mower deck not level.

2.

Level mower deck.

 

3.

Buildup of grass, leaves, and trash under mower.

3.

Clean underside of mower housing.

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

5.

Clogged mower deck vent holes from buildup of

5.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Mower blades will not

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

Poor grass discharge

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

4.

Mower deck not level.

4.

Level mower deck.

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

6.

Worn, bent or loose blade.

6.

Replace/sharpen blade. Tighten blade bolt.

 

7.

Buildup of grass, leaves and trash under mower.

7.

Clean underside of mower housing.

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

10.

Improper blades used.

10.

Replace with blades listed in this manual.

 

11.

Clogged mower deck vent holes from buildup of

11.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Headlight(s) not working

1.

Switch is “OFF”.

1.

Turn switch “ON”.

(if so equipped)

2.

Bulb(s) burned out.

2.

Replace bulb(s).

 

3.

Faulty light switch.

3.

Check/replace light switch.

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

Battery will not charge

1.

Bad battery cell(s).

1.

Replace battery.

 

2.

Poor cable connections.

2.

Check/clean all connections.

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

Loss of drive

1.

Freewheel control in “disengaged” position.

1.

Place freewheel control in “engaged” position.

 

2.

Motion drive belt worn, damaged, or broken.

2.

Replace motion drive belt.

 

3.

Air trapped in transmission during shipment

3.

Purge transmission.

 

 

or servicing.

 

 

 

 

 

 

 

Engine “backfires”

1.

Engine throttle control not set at “SLOW”

1.

Move throttle control to “SLOW” position and allow

when turning engine

 

position for 30 seconds before stopping engine.

 

to idle for 30 seconds before stopping engine.

“OFF”

 

 

 

 

 

 

 

 

 

26

Image 26
Contents Model NO. S165H42A Safety Rules Safe Operation Practices for Ride-On MowersTable of Contents Product Specifications Customer ResponsibilitiesKey Unassembled PartsSteering Wheel Seat Slope SheetHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Lower seat into operating position and sit on seatCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations ¿ Lubrication ChartCustomer Responsibilities Before Each USETractor Engine Muffler CleaningAIR Filter Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigBelt Installation Belt RemovalTo Adjust Steering Wheel Alignment Transaxle Motion Control Lever Neutral Adjustment See FigTransmission REMOVAL/REPLACEMENT To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number S165H42AElectrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly KEY Part NO. NO.DESCRIPTION Engine 170551 Control Throt/Ch Seat Assembly Decals Wheels & TiresMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Repair Parts Service Notes Limited Warranty Limited Warranties ForSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill

177019 specifications

The Weed Eater 177019 is a powerful and versatile string trimmer designed for homeowners and landscape enthusiasts alike. With its ease of use and efficient performance, it has become a popular choice for those looking to maintain neat and tidy lawns, gardens, and outdoor spaces.

One of the standout features of the Weed Eater 177019 is its 17-inch cutting width. This wide cutting path allows users to tackle larger areas in less time, making it ideal for properties of varying sizes. The trimmer is equipped with a reliable and robust 25cc 2-cycle engine, providing enough power to handle tough weeds and overgrown grass. The lightweight design, weighing only 10.3 pounds, offers excellent maneuverability, reducing arm fatigue during extended use.

The Weed Eater 177019 features an adjustable telescoping shaft, allowing users to customize the length according to their height and comfort. This ergonomic design enhances user experience, making it suitable for people of all sizes. The soft-grip handle provides additional comfort and control, enabling users to maintain precision while trimming around flower beds and garden borders.

Another impressive characteristic of this trimmer is its automatic line advancement system. This technology ensures that the trimmer line is advanced smoothly and easily, eliminating the hassle of manual adjustments. Users simply tap the head of the trimmer on the ground while in use to release more line, allowing for continuous cutting without interruptions.

The Weed Eater 177019 also incorporates a dual-line system that effectively increases cutting efficiency. This feature allows for a cleaner and more accurate cut, reducing the risk of damaging surrounding plants and structures. The easy-loading spool further simplifies maintenance, enabling users to quickly replace the trimmer line without hassle.

For added convenience, the Weed Eater 177019 is designed for easy starting. Its spring-assisted starter reduces pull resistance, making it simpler for users to get the trimmer up and running. This user-friendly design is a significant advantage, especially for those who may be less experienced with power tools.

In summary, the Weed Eater 177019 is an efficient string trimmer packed with features that promote ease of use and effective lawn care. With its powerful engine, adjustable design, automatic line advancement, and user-friendly operation, it proves to be a reliable choice for anyone looking to keep their outdoor spaces well-groomed. Its combination of performance and comfort makes it a valuable addition to any homeowner's tool collection.