Weed Eater 182983 manual Tractor, Brake Operation, Tires, Operator Presence System, Blade Care

Page 15

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 8)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer secur- ing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

MANDREL

TRAILINGASSEMBLY EDGE UP

CENTER

HOLE

LOCK WASHER

STAR

BLADE

FLAT WASHER

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 8

TO SHARPEN BLADE (See Fig. 9)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 9

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model NO. WE1538B II. Slope Operation Safety RulesIV. Service General OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Steering Wheel Seat Unassembled PartsTo Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorLower seat into operating position and sit on seat Install Seat See FigCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Check Engine OIL Level Before Starting the EngineTo Operate on Hills To Transport Towing Carts and Other ATTACH- MentsTo Start Engine See Fig Mowing TipsGeneral Recommendations Lubrication ChartService Dates Customer ResponsibilitiesOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsEngine Cooling Fins See Fig Clean AIR ScreenTo Service PRE-CLEANER To Service CartridgeIN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Adjust Brake See Fig To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Remove CABLES, Reverse Order To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WE1538B SchematicElectrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering 140044X428 Spark Arrester Optional Equipment170551 Control Th/ch Flag Seat LBD48 DecalsWheels & Tires LSB42Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

182983 specifications

The Weed Eater 182983 is a versatile and efficient tool designed for homeowners and landscaping professionals alike who require a reliable solution for their gardening and lawn maintenance needs. This trimmer is engineered to make yard work less of a chore, combining power, portability, and ease of use into its design.

One of the main features of the Weed Eater 182983 is its lightweight and ergonomic design, which ensures user comfort during extended use. Weighing in at just over 10 pounds, this trimmer is easy to maneuver, reaching tight spots and tackling overgrown areas without causing strain on the user's arms or back. The adjustable handle allows for a customizable grip, fitting a variety of user heights and preferences.

Powered by a robust 18-volt lithium-ion battery, the Weed Eater 182983 provides a significant run time with fade-free power. This technology enables the user to work for longer periods without the need for constant recharging. Additionally, the battery is designed to fully charge in approximately one hour, making it convenient for quick touch-ups or more extensive landscaping projects.

Another significant aspect of the 182983 model is the innovative 2-in-1 functionality. This weed eater is equipped with a cutting head that supports both string and blade trimming, allowing users to switch between different cutting methods based on the task at hand. The string trimmer is ideal for finer grass and weeds, while the blade system is effective for tougher vegetation and thicker brush.

The Weed Eater 182983 also features an automatic feed spool, which ensures that the cutting line is consistently at the optimal length for effective trimming. This technology eliminates the need for manual line advancement, streamlining the trimming process and enhancing efficiency.

Durability is another characteristic of the Weed Eater 182983, with its sturdy construction designed to withstand the rigors of outdoor use. The materials used in its manufacture are both lightweight and long-lasting, ensuring that this tool remains effective over time with proper care.

In summary, the Weed Eater 182983 stands out for its combination of a lightweight design, powerful battery, 2-in-1 functionality, and ease of use. It is an ideal choice for anyone looking to maintain their lawn and garden while minimizing effort and maximizing results.
Top Page Image Contents