Weed Eater 182983 manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

1/2" wrenches

Pliers

(1)

9/16" wrench

Tire pressure gauge

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

 

INSERT

 

1/2 HEX NUT

 

LARGE FLAT

 

WASHER

STEERING

STEERING

BOOT

WHEEL

 

 

TABS

ADAPTER

 

 

EXTENSION SHAFT

 

1/4 HEX BOLT

1/4 LOCKNUT

 

LOWER

TAB

SLOTS

STEERING

 

SHAFT

 

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO

FIG. 1

10-12 FT. LBS TORQUE.

 

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 1/2 hex nut and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

HOW TO SET UP YOUR TRACTOR

CHECK BATTERY (See Fig. 2)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See “BATTERY” in the Customer Responsibilities sec- tion of this manual for charging instructions).

SEAT PAN

LABEL

FIG. 2

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model NO. WE1538B General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering Wheel SeatHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Lower seat into operating position and sit on seatCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other ATTACH- Ments Before Starting the EngineTo Operate on Hills To Transport Check Engine OIL LevelMowing Tips To Start Engine See FigCustomer Responsibilities Lubrication ChartService Dates General RecommendationsTires TractorBrake Operation Operator Presence SystemBelts BatteryEngine Transaxle CoolingTo Service Cartridge Clean AIR ScreenTo Service PRE-CLEANER Engine Cooling Fins See FigSpark Plugs CleaningMuffler IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Brake See Fig To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove CABLES, Reverse OrderInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WE1538BElectrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering 140044X428 Optional Equipment Spark Arrester170551 Control Th/ch Flag Seat LSB42 DecalsWheels & Tires LBD48Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

182983 specifications

The Weed Eater 182983 is a versatile and efficient tool designed for homeowners and landscaping professionals alike who require a reliable solution for their gardening and lawn maintenance needs. This trimmer is engineered to make yard work less of a chore, combining power, portability, and ease of use into its design.

One of the main features of the Weed Eater 182983 is its lightweight and ergonomic design, which ensures user comfort during extended use. Weighing in at just over 10 pounds, this trimmer is easy to maneuver, reaching tight spots and tackling overgrown areas without causing strain on the user's arms or back. The adjustable handle allows for a customizable grip, fitting a variety of user heights and preferences.

Powered by a robust 18-volt lithium-ion battery, the Weed Eater 182983 provides a significant run time with fade-free power. This technology enables the user to work for longer periods without the need for constant recharging. Additionally, the battery is designed to fully charge in approximately one hour, making it convenient for quick touch-ups or more extensive landscaping projects.

Another significant aspect of the 182983 model is the innovative 2-in-1 functionality. This weed eater is equipped with a cutting head that supports both string and blade trimming, allowing users to switch between different cutting methods based on the task at hand. The string trimmer is ideal for finer grass and weeds, while the blade system is effective for tougher vegetation and thicker brush.

The Weed Eater 182983 also features an automatic feed spool, which ensures that the cutting line is consistently at the optimal length for effective trimming. This technology eliminates the need for manual line advancement, streamlining the trimming process and enhancing efficiency.

Durability is another characteristic of the Weed Eater 182983, with its sturdy construction designed to withstand the rigors of outdoor use. The materials used in its manufacture are both lightweight and long-lasting, ensuring that this tool remains effective over time with proper care.

In summary, the Weed Eater 182983 stands out for its combination of a lightweight design, powerful battery, 2-in-1 functionality, and ease of use. It is an ideal choice for anyone looking to maintain their lawn and garden while minimizing effort and maximizing results.
Top Page Image Contents