Weed Eater 182983 To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 16 and 17)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

BOTTOM EDGE

OF MOWER

OF MOWER

TO GROUND

TO GROUND

“A”

“A”

 

GROUND LINE

FIG. 16

SUSPENSION ARM

LIFT LINK

ADJUSTMENT

NUT

FIG. 17

FRONT-TO-BACK ADJUSTMENT (See Figs. 18 and 19)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 18

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 19

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 20)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Disconnect R.H. suspension arm from rear deck bracket by removing retainer spring.

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Work new belt around both mandrel pulleys and idler pulleys.

•Install new belt into engine pulley grove.

•Reconnect R.H. suspension arm and secure with re- tainer spring.

•Make sure belt is in all pulley grooves and inside all belt guides.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model NO. WE1538B Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering Wheel SeatAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Lower seat into operating position and sit on seatCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Operate on Hills To TransportTowing Carts and Other ATTACH- Ments Check Engine OIL LevelMowing Tips To Start Engine See FigLubrication Chart Service DatesCustomer Responsibilities General RecommendationsTractor Brake OperationTires Operator Presence SystemBattery EngineBelts Transaxle CoolingClean AIR Screen To Service PRE-CLEANERTo Service Cartridge Engine Cooling Fins See FigCleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalFront Wheel TOE-IN/CAMBER To Adjust Brake See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WE1538BElectrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering 140044X428 Optional Equipment Spark Arrester170551 Control Th/ch Flag Seat Decals Wheels & TiresLSB42 LBD48Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

182983 specifications

The Weed Eater 182983 is a versatile and efficient tool designed for homeowners and landscaping professionals alike who require a reliable solution for their gardening and lawn maintenance needs. This trimmer is engineered to make yard work less of a chore, combining power, portability, and ease of use into its design.

One of the main features of the Weed Eater 182983 is its lightweight and ergonomic design, which ensures user comfort during extended use. Weighing in at just over 10 pounds, this trimmer is easy to maneuver, reaching tight spots and tackling overgrown areas without causing strain on the user's arms or back. The adjustable handle allows for a customizable grip, fitting a variety of user heights and preferences.

Powered by a robust 18-volt lithium-ion battery, the Weed Eater 182983 provides a significant run time with fade-free power. This technology enables the user to work for longer periods without the need for constant recharging. Additionally, the battery is designed to fully charge in approximately one hour, making it convenient for quick touch-ups or more extensive landscaping projects.

Another significant aspect of the 182983 model is the innovative 2-in-1 functionality. This weed eater is equipped with a cutting head that supports both string and blade trimming, allowing users to switch between different cutting methods based on the task at hand. The string trimmer is ideal for finer grass and weeds, while the blade system is effective for tougher vegetation and thicker brush.

The Weed Eater 182983 also features an automatic feed spool, which ensures that the cutting line is consistently at the optimal length for effective trimming. This technology eliminates the need for manual line advancement, streamlining the trimming process and enhancing efficiency.

Durability is another characteristic of the Weed Eater 182983, with its sturdy construction designed to withstand the rigors of outdoor use. The materials used in its manufacture are both lightweight and long-lasting, ensuring that this tool remains effective over time with proper care.

In summary, the Weed Eater 182983 stands out for its combination of a lightweight design, powerful battery, 2-in-1 functionality, and ease of use. It is an ideal choice for anyone looking to maintain their lawn and garden while minimizing effort and maximizing results.
Top Page Image Contents