HOW to Stop Your Unit

IMPORTANT

Experience indicates that alcohol blended fuels (called gasohol or using ethanol or metha- nol) can attract moisture which leads to separa- tion and formation of acids during storage. Acid- ic gas can damage the fuel system of an engine while in storage. To avoid engine problems, empty the fuel system before storage for 30 days or longer. Drain the gas tank, start the en- gine and let it run until the fuel lines and carbure- tor are empty. Use fresh fuel next season.

Never use engine or carburetor cleaner prod- ucts in the fuel tank or permanent damage may occur. See the STORAGE section for addi- tional information.

S To stop the engine, move the ON/OFF switch to the OFF position.

SIf engine does not stop, move choke to the FULL CHOKE position.

Engine Choke Lever

ON/OFF

Switch

FULL HALF OFF

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

1.Set unit on a flat surface.

2.Move ON/OFF switch to the ON position.

3.Slowly press the primer bulb 6 times.

4.Move choke lever to the FULL CHOKE position.

5.Squeeze the throttle trigger fully and hold through all remaining steps.

Starter Handle

Choke

Lever

Muffler

Primer Bulb

6.Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

7.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

8.Pull starter rope sharply until engine runs, but no more than 6 pulls.

NOTE: If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the start- er rope until the engine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably flooded. Proceed to

STARTING A FLOODED ENGINE.

9.Once the engine starts, allow it to run 10 seconds, then move the choke lever to the OFF CHOKE position. Allow the unit to run for 30 more seconds at OFF CHOKE before releasing the throttle trig- ger.

NOTE: If engine dies with the choke le- ver in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move ON/OFF switch to the ON position.

2.Move the choke lever to the HALF CHOKE position.

3.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the en- gine runs smoothly.

4.Pull starter rope sharply until engine runs, but no more than 5 pulls.

5.Allow engine to run 15 seconds, then move the choke lever to OFF CHOKE.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex- cess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded.

If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

530086935 specifications

The Weed Eater 530086935 is a reliable and efficient string trimmer designed for homeowners and gardeners seeking a powerful, easy-to-use tool for maintaining their outdoor spaces. This versatile equipment is engineered to make lawn care tasks more manageable, whether you are tackling overgrown grass, weeds, or trimming around fences and trees.

One of the standout features of the Weed Eater 530086935 is its powerful engine, which offers a commendable balance of power and efficiency. This gas-powered trimmer is designed to handle tough vegetation, making it an ideal choice for homeowners with larger yards or areas requiring regular maintenance. The engine is engineered for optimal performance, with features that reduce emissions and enhance fuel efficiency, ensuring that you can work longer with fewer interruptions.

The cutting head of the Weed Eater 530086935 is equipped with a dual-line spool system that allows for a 0.080-inch line diameter. This feature ensures that you can achieve a clean, precise cut while minimizing downtime on line replacement. The easy-loading spool mechanism allows users to quickly reload the trimmer line, making it more convenient to switch tasks and keep the trimmer operational.

The adjustable handle is another significant characteristic of this trimmer, providing users with added comfort and control during operation. The ergonomic design helps reduce fatigue during prolonged use, allowing you to tackle larger areas without discomfort. Furthermore, this trimmer features a straight shaft, which is suitable for reaching under shrubs and around obstacles, enhancing versatility.

The Weed Eater 530086935 also incorporates various user-friendly technologies, including a simple start system that minimizes the effort required to start the engine. This important feature is particularly advantageous for those who may struggle with traditional pull-start mechanisms.

In terms of maintenance, the trimmer's design facilitates easy access to vital components, ensuring that routine checks and repairs are hassle-free. The Weed Eater 530086935 strikes a perfect balance between power, efficiency, and ease of use, making it an excellent investment for anyone looking to keep their lawn and garden well-groomed. With its combination of advanced features and thoughtful design, this trimmer stands out as a dependable choice in the world of outdoor power equipment.