Line Replacement, Carburetor Adjustment

LINE REPLACEMENT

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with a pre-wound spool, or cut two lengths of 12-1/2feet of 0.080! (2 mm) di- ameter Weed Eaterr brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert ends of the lines about 1/2 inch (1 cm) into the small holes on the inside of spool.

SpoolSmall Holes

Line exit holes					Line in Notch

Line in Notch

Hub

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

6.Push the lines into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the lines into the exit holes in the hub as shown in the illustration.

8.Align the notches with the line exit holes.

9.Push spool into hub until it snaps into place.

10.Pull the lines extending outside of the hub to release the lines from the notches.

CARBURETOR ADJUSTMENT

Your carburetor is equipped with limiter caps. Carburetor adjustment is a complicated task. We recommend that you take your unit to an authorized service dealer. Damage will occur if you turn the needles beyond the limiter stops.

WARNING: Perform the following steps after each use:

S Allow engine to cool, and secure the unit before storing or transporting.

SStore unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric

motors or switches, furnaces, etc.

SStore unit with all guards in place. Position unit so that any sharp object cannot acci-

dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

SClean the entire unit before lengthy storage. S Store in a clean dry area.

S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol- low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom-

mended type and heat range.

SClean air filter.

S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

S At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

SDo not store gasoline from one season to another.

S Replace your gasoline can if it starts to rust.

530163506 specifications

The Weed Eater 530163506 is a versatile and efficient lawn care tool designed to tackle overgrown grass and stubborn weeds with ease. This gas-powered string trimmer is particularly notable for its reliability and performance, making it an essential addition to any gardener or landscaper’s toolkit.

One of the standout features of the Weed Eater 530163506 is its 25cc 2-cycle engine. This powerful engine provides the necessary strength to cut through thick vegetation effortlessly, reducing the amount of time and effort required for yard maintenance. The engine is designed for easy starting, thanks to its advanced recoil system, allowing users to get to work quickly without frustrating delays.

The lightweight and ergonomically designed frame contribute to enhanced maneuverability. Weighing in at just around 10 pounds, it allows for extended use without causing excessive fatigue. The adjustable handle can be modified to a comfortable height, ensuring that users of varying statures can operate the machine effectively.

One of the defining characteristics of this model is its dual-line cutting head, which utilizes a bump-feed mechanism. This allows for easy line advancement, simply tapping the head on the ground while in use. The .065-inch diameter line efficiently tackles grassy areas and small weeds, providing a clean cut with every pass.

Durability is another key aspect of the Weed Eater 530163506. The fiberglass-reinforced shaft is not only lightweight but also resistant to bending and breaking, ensuring longevity and reliable performance even in the toughest conditions. Moreover, the trimmer boasts a straight shaft design, which offers greater reach and allows users to easily access hard-to-reach areas like beneath bushes or around trees.

The optional attachment capabilities further enhance its usability. Users can purchase various attachments, transforming the trimmer into a blower, edger, or hedge trimmer, making it a multi-functional tool for all lawn care needs. This versatility can save both time and money, as it eliminates the need for multiple standalone devices.

In summary, the Weed Eater 530163506 is engineered for high performance, ease of use, and multi-functionality. With its powerful engine, lightweight design, versatile cutting head, and durability, it stands out as a top choice for homeowners and professionals alike looking for an all-in-one solution for effective lawn maintenance.