Sears 247.34625 owner manual Retainer Cover, AIR Cleaner, Clean Engine, Clean Out Dirt, Spark Plug

Page 14

Your four-cycle engine will normally consume some oil; therefore, check engine oil level regularly--

approximately every five hours of operation and before each usage. Stop engine and wait several minutes before checking oil level. With engine level, the oil must be to the FULL mark on dipstick (refer to figure 11). Change engine oil after the first five hours of operation, and every twenty-five hours thereafter.

Retainer

Cover

,ase

Pre-Cleaner

 

Slot

 

 

To Drain Oil:

Drain oil while engine is warm,

a, Remove oil drain plug. Catch oil in a suitable container.

b.When engine is drained of all oil, replace drain plug securely.

Refill with fresh oil. Refer to GAS AND OIL FILL- UP section.

Replace dipstick.

AIR CLEANER

The air cleaner prevents damaging dirt, dust, etc., from entering the carburetor and being forced into the

engine and is important to engine life and per- formance.

Never run your engine without air cleaner com- pletely assembled.

To Service Air Cleaner:

Service pre-cleaner after every 25 hours of use, or at least once a season. Service cartridge every 100 hours of use, or at least once a season. Service pre-cleaner and cartridge more often under dusty conditions.

Loosen air cleaner cover screws. Remove cover and air cleaner assembly from base. See figure 15.

Remove air cleaner assembly from inside cover and disassemble.

To service foam pre-cleaner: Remove pre-cleaner. Wash in liquid detergent and water. Squeeze dry in a clean cloth. Saturate in engine oil. Squeeze in a clean, absorbent cloth to remove all excess oil. If pre-cleaner is very dirty, replace it.

To service cartridge: Clean by tapping gently on a flat surface, tf very dirty, replace. Do not oi! cartridge.

NOTE: Do not use petroleum solvents (e.g. kerosene) or pressurized air to clean cartridge. They will cause cartridge to deteriorate.

Reassemble retainer on pre-cleaner and cartridge (screen side of pre-cleaner toward cartridge pleats). Place assembly into cover.

Insert tabs on cover into slots in base and tighten cover screws securely.

Cover

Screws

FIGURE 15.

CLEAN ENGINE

Clean engine periodically. Remove dirt and debris

with a cloth or brush. Cleaning with a forceful spray of water is not recommended as water could contami-

nate the fuel system.

Yearly or every 25 hours, whichever occurs first, remove the blower housing and clean the areas shown in figure 16 to avoid overspeeding, overheating and engine damage. Clean more often if necessary.

WARNING: PERIODICALLY CLEAN MUF-

FLERDIRT ANDAREACOMBUSTIBLETO REMOVE DEBRISALL GRASS,.

Clean Out

and

Dirt

FIGURE 16.

SPARK PLUG

The spark plug should be cleaned and the gap reset to .030" at least once a season or every 50 hours of operation. See figure 17. Spark plug replacement is recommended at the start of each season. Refer to engine parts list for correct spark plug type.

NOTE: Do not sandblast spark plug. Spark plug should be cleaned by scraping or wire brushing and washing with a commercial solvent.

.030" Feeler Gauge

Spark Plug

FIGURE 17.

14

Image 14
Contents Crrftsmrn Training OperationCustomer Responsibilities TowingMaintenance Agreement Oneyearlimitedwarrantyon CraftsmanlogsplitterProduct Specifications Customer ResponsibilitiesPlugOil AccessoriesIndex Unpacking Assembly InstructionsToolsrequiredforassembly Assemblingyour LOG SplitterPlace the hose clamp at the base of the fitting, Final AssemblyAttachingthehoses Return HoseKnowyourlogsplitter Meets Ansi Safety RequirementsOperation STARTERHANDLE--Used to manuallystartTo Stop Engine HOW to USE Your LOG SplitterUsing the Control Handle Raising and Lowering BeamDipstick Gasand OIL FILL-UPBeforeeachuse Tostartengine Beforeinitial USECustomer Responsibilities Maintenance ScheduleAS YOU Complete Regular Service To StopengineEngine GeneralrecommendationsLogsplitter Clean Out Dirt AIR CleanerClean Engine Retainer CoverOther StorageLOG Splirer Carburetoradjustment ServiceAdjustments ThrottleadjustmentRPM EnginespeedTires Idle Speed Screw ValvePossible Causes Trouble ShootingProblem Corrective ActionHydraulic Trouble Shooting GuideRepair Parts NO. no 614 200984 305ATo Install See Repair Instruction Manual 22O634 634A429 188832 182461 335 363 356883 134Horsepower 25.5 TON Hydraulic LOG Splitter 770-8766K 8/94