Sears 919.32721 Before Starting Engine, Connecting Generator To Main Electrical Supply, Gasoline

Page 12

Connecting Generator To Main Electrical

Supply

Potential hazards exist when a electrical generator is con- nected to the main electrical supply coming into the house. It is at that point that the generator could feed back into the utility company's system causing possible electrocution of workers who are repairing electrical lines. To avoid back feeding of electricity into utility systems, a double-throwtransfer switch should be installed between the genera- tor and utility power. This device should be installed by a licensed electrician and in compliance with all local electri- cal codes.

NOTE: When installing a Double-ThrowTransfer Switch, a minimum of 10 gauge wiring must be used.

BEFORE STARTING ENGINE

every start. Running engine low of oil or out of oil

I CAUTION: Always check engine oil level before could result in serious damage to the engine.

Adding Engine Oil

Your generator has been shipped without oil in the engine. Begin by removing the oil dipstick and plug. Start pouring the oil in slowly.

The engine will hold approximately 26 ounces of oil. To check the oil, clean and replace the dipstick. Do not screw the dip stick in when checking the oil level. Next, remove the dipstick to check the level. The oil dipstick is clearly marked with lines that tell you when the engine has enough oil. Do not fill above this point.

CLEAN

DIPSTICK

NOTE: When adding oil to the engine crankcase, use a high quality detergent oil classified "For Service SF,SG,SH" rated SAE 30 weight. Use no special additives. Select the oil'sviscosity grade according to your expected operating temperatures.

SAE Viscosity Grades

IT

TARTI NG TEMPERATLIR1E RANGE_ANTICIPATED BEFORE NEXT_IL CHANGE

Low Oil Shutdown

Your Sears generator engine is equipped with Low Oil Shutdown. Low Oil Shutdown is a safety device de-

signed to protect your engine from damage in the event the oil level in the crankcase is low.

If while the engine is running, the oil gets low, it will automatically shut itself down and will not restart until the

oil is added. If the oil is low before start-up, the genera- tor will not start until oil is added.

NOTE: The Low Oil Shutdown mechanism is very sensi- tive. You must fill the engine to the full mark on the dipstick to inactivate this safety device.

Gasoline

Your generator engine is 4 cycle. Use unleaded fuel only. Never mix oil with gasoline.

CAUTION: Never fill fuel tank completely. Fill tank to 1/2" below the bottom of the filler neck to provide space for fuel expansion. Wipe any fuel spillage from engine and equipment before starting engine.

tank when engine is running or hot. Do not smoke I I WARNING: Never fill fuel tank indoors. Never fill fuel

when filling fuel tank.

Use clean, fresh, regular unleaded gasoline with a mini- mum of 85 octane. Do not mix oil with gasoline. If unleaded fuel is not available, leaded fuel may be used.

To Start Your Generator

I

poor ventilated areas. Engine exhaust contains car-

ICAUTION: Never run engine indoors or in enclosed, I

bon monoxide, an ordorless and deadly gas.l

Make sure the fuel shutoff valve is turned to the open position.

CLOSE

OPEN__

•Remove gas cap.

•Add unleaded gasoline, slowly, to fuel tank.

•Do not overfill.

•On the engine there is a start/off switch located

on the front panel of the engine. Place this switch to the start position.

12 -- ENG

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Owners Manual Table of Contents Safety Guidelines Definitions Hazard What could Happen HOW to Prevent ITRisk of Electrocution and Fire Informationfor preventingdamage toRisk of Electrocution and Fire contd Risk of Fire Operate Unit Indoors or ANY Confined AreaRisk of Breathing Inhalation Hazard HazardRisk of Unsafe Operation Risk of HOT SurfacesRisk of Moving Parts Carton Contents Risk from LiftingRemove Generator from Carton Installing Wheel KIT Not rub frame if installed properlyGrounding the Generator Key No. DescriptionEngine RUN/STOP SWITCH- Sets engine in starting Know Your GeneratorVolt Twistlock RECEPTACLE- Used to Receptacles Generator CapacityObtaining Electricity from Generator Volts X Amp = WattsConnecting Generator To Main Electrical Supply Before Starting EngineAdding Engine Oil Low Oil ShutdownConnecting Electrical Loads Customer ResponsibilitiesStopping The Engine Maintnenance TaskGenerator Maintenance Engine MaintenanceGeneral Recommendations Storage Instructions Problem Cause Correction Frame Assembly KEYDescription Part Number Fuel TAN K Screws Fuel TankRotor Assembly Stator AssemblyTorque to 120-144-IN-LBS Torque to 30-40 IN-LBS Scale KEY Description Part Number Drive END AdapterKEY NO. Description GS-0207 SSF-595 SSF-584 SS-1525-CD281 \ RERNO. Partno REE no Partno Description RERNO. PARTNO. Description California & US EPA Emission Control Warranty Statement Manufacturers Emission Control System Warranty CoverageOwners Warranty Responsibilities Important NoteEmission Control System Warranty EMISSION-RELATED Parts Include the FollowingHomeCentraF

919.32721 specifications

The Sears 919.32721 is a remarkable addition to the world of portable electronics, boasting a unique intersection of functionality, style, and technological advancement. Primarily recognized as a versatile multimeter, this device serves not only as a measurement tool for electricians but also appeals to hobbyists and professionals alike.

One of the main features of the Sears 919.32721 is its comprehensive measurement capabilities. It excels in measuring voltage, current, and resistance, making it an essential tool for diagnosing electrical issues in a variety of applications. The device offers both AC and DC voltage measurements, covering a broad range from household circuits to automotive systems. This feature enhances its usability, ensuring that the device can cater to different needs across multiple fields.

The design and user interface of the Sears 919.32721 are crafted with user experience in mind. It features a clear, easy-to-read LCD display that provides accurate readings in real-time, allowing users to make quick decisions during troubleshooting. The buttons are intuitively placed, providing easy navigation through various functions and settings, and the overall ergonomics of the device ensure comfort during prolonged use.

Technologically speaking, the multimeter is equipped with advanced circuitry that enhances measurement precision and stability. It employs true RMS technology, which allows the meter to deliver accurate readings even in the presence of non-sinusoidal waveforms, thus making it more reliable for various applications. Additionally, the Sears 919.32721 has built-in safety features such as overload protection, which safeguards the device from damage in the event of improper usage.

Portability is another defining characteristic of the Sears 919.32721. It is compact and lightweight, making it easy to carry around in toolboxes or pockets. This mobility facilitates on-site measurements, which is a significant advantage for technicians and engineers who work in diverse environments.

In conclusion, the Sears 919.32721 stands out in the market for its robust feature set and user-friendly design. It bridges the gap between technology and usability, making it an indispensable tool for anyone involved in electrical measurements and diagnostics. Whether for professional use or DIY projects, this multimeter delivers reliability and precision, ensuring that users can tackle any electrical task with confidence.
Top Page Image Contents