McCulloch M19542H manual Tractor, Blade Removal See Fig, Battery

Page 16

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments sec- tion of this manual).

TIRES

•Maintain proper air pressure in all tires Set to PSI shown on tire.

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

828

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Useonlyareplacementblade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 10)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: Special blade bolt is heat treated.

BLADE

STAR

 

 

 

 

02

545

 

 

 

 

MANDREL

 

 

ASSEMBLY

BLADE BOLT

CENTER

 

(SPECIAL)

HOLE

 

Fig. 10

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model NO. M19542H 19.5 HP 42 Inch Lawn Tractor Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig Check Battery See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Using the Reverse Operation System Reverse Operation System ROSTo Operate on Hills To Operate Mower See FigBefore Starting the Engine To TransportTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission Mowing TipsAutomatic Transmission Warm UP Maintenance Lubrication ChartTractor BatteryBlade Removal See Fig Transaxle Maintenance EngineBelts Transaxle CoolingCleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Check Brake To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

M19542H specifications

The McCulloch M19542H is a robust and versatile lawn mower designed to cater to the needs of both residential and professional users. This high-performance machine boasts a combination of advanced technology and user-friendly features, making it a top choice for tackling various mowing tasks.

One of the standout features of the M19542H is its powerful 195cc engine. This engine is designed to provide exceptional torque and cutting power, enabling the mower to handle thick grasses and uneven terrains with ease. The reliable starting system ensures that users can begin their mowing sessions without the frustration of difficult starts, allowing for a smooth and efficient operation.

The mower is equipped with a wide 42-inch cutting deck, which not only allows for quick mowing of larger areas but also provides an adjustable cutting height. This feature grants users the flexibility to choose from several cutting heights, ensuring the perfect lawn finish whether aiming for a manicured look or a more natural appearance.

Another notable characteristic of the McCulloch M19542H is its innovative twin-blade system. This design enhances cutting efficiency, producing finely mulched grass clippings that can be recycled back into the lawn. This not only improves the overall health and appearance of the lawn but also reduces the amount of waste generated during the mowing process.

Comfort is paramount in the design of the M19542H. The adjustable ergonomic handle ensures that users can maintain a comfortable grip and posture while mowing, reducing fatigue during prolonged use. Additionally, the mower features a compact and maneuverable design, allowing for easy navigation around obstacles and tight spaces.

Safety is also a key consideration in the design of the McCulloch M19542H. The mower is equipped with various safety features, including a blade brake that stops the mower's blades when the user releases the handle, ensuring peace of mind during operation.

In terms of maintenance, the M19542H is designed for convenience. The easy-access oil and air filters make routine checks and replacements simple, promoting optimal performance longevity. Overall, the McCulloch M19542H combines power, efficiency, and user-friendly design, making it an excellent choice for anyone looking to maintain a pristine lawn with minimal effort.
Top Page Image Contents