McCulloch 96042011400, MC195H42LT Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

5/16" wrench

Utility knife

(2)

7/16" wrenches

Tire pressure gauge

(2) 1/2" wrenches

Pliers

(1)

9/16" wrench

 

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, lock washer, bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

TO CHECK BATTERY (See Fig. 1)

•Lift seat to raised position.

NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

•For battery and battery cable installation see "RE- PLACING BATTERY" in the "Service and Adjustments" section in this manual.

LABEL

Fig. 1

ATTACH STEERING WHEEL (See Fig. 2)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

BOLT

LARGE FLAT

LOCK

WASHER

WASHER

 

 

STEERING

 

WHEEL

 

STEERING

 

BOOT

 

ADAPTER

LOWER

 

STEERING

EXTENSION

SHAFT

 

SHAFT

Fig. 2

INSTALL SEAT (See Figs. 3 and 4)

•Remove bolt and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. Remove the cardboard packing and discard.

•Connect switch to seat.

•Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan.

•Push down on seat to engage pads in slots and pull seat towards rear of tractor.

•Raise seat and tighten bolt securely.

•Remove tape and discard.

•Lower seat into operating position and sit on seat. Press clutch/brake pedal all the way down. If operating position is not comfortable, adjust seat.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Operators Manual General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering WheelTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Deck Levelness To Adjust Seat See FigCheck Tire Pressure Check for Proper Position of BeltsOperation Know Your Tractor ROS onPosition Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control See FigReverse Operation System ROS To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerBefore Starting the Engine Check Engine OIL Level To Operate on HillsTowing Carts and Other Attachments ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP General Recommendations MaintenanceMaintenance ScheduleBattery TractorBlade Removal See Fig Engine AIR Filter Clean AIR ScreenCleaning MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transaxle Motion Control Lever Neutral Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionTroubleshooting Points Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty

532 43 25-35, 96042011400, MC195H42LT specifications

The McCulloch MC195H42LT is a versatile lawn tractor designed for homeowners looking for a reliable and efficient machine to maintain their lawns. This tractor is particularly noteworthy for its blend of power, precision, and user-friendly features, making it a great choice for both novice and experienced users.

One of the standout features of the MC195H42LT is its powerful engine. It is equipped with a robust 532cc engine that provides ample power for tackling various lawn care tasks. The engine operates smoothly and starts easily, ensuring that users can get to work without hassle. The mowing deck, measuring 42 inches, is designed for efficient cutting, allowing for faster mowing times while delivering a clean and precise cut.

In terms of technology, the McCulloch MC195H42LT includes a hydrostatic transmission system. This system allows for seamless speed adjustments without the need for manual gear shifting. The result is a smooth driving experience and improved maneuverability on different terrains. Additionally, the tractor features a turning radius that makes it easy to navigate around trees, flower beds, and other obstacles in the yard.

The comfort of the operator is also a priority in the design of the MC195H42LT. It comes with an adjustable seat, ensuring that users of varying heights can find a comfortable driving position. This is complemented by easy-to-access controls that allow for effortless operation of the tractor's functions, such as cutting height adjustments.

Another important characteristic is its ease of maintenance. The design of the lawn tractor includes features that simplify routine care, enabling users to spend more time mowing and less time on upkeep. For those looking to enhance their lawn care experience, there are additional accessories available, such as towing carts and mulching kits.

Overall, the McCulloch MC195H42LT is a well-rounded lawn tractor that offers a powerful engine, user-friendly technology, and comfort for the operator. Its design effectively meets the demands of homeowners seeking an efficient and reliable machine for maintaining their lawns while also providing options for customization and enhanced functionality.
Top Page Image Contents