Troy-Bilt 12190-3HP Introduction, Inspect unit, Tools/Materials Needed for Assembly, Section

Models: 12214 - 5.5HP 12190-3HP

1 28
Download 28 pages 16.2 Kb
Page 6
Image 6
2Assembly

Section

2Assembly

WARNING

To prevent personal injury or property damage, do not start the engine until all assembly steps are complete and you have read and understand the safety and operating instruc- tions in this manual.

Introduction

Carefully follow these assembly steps to correctly prepare your tiller for use. It is recommended that you read this Section in its entirety before beginning assembly. NOTE: If an assembly step applies only to certain models, those models are noted at the beginning of that step. Otherwise, a step applies to all models.

Inspect unit

Inspect the unit and carton for damage immediately after delivery. Contact the carrier (trucking company) if you find or suspect damage. Inform them of the damage and request instructions for filing a claim. To protect your rights, put your claim in writing and mail a copy to the carrier within 15 days after the unit has been delivered. Contact us at the factory if you need assistance in this matter.

STEP 1: Unpacking Instructions

1.Remove any cardboard inserts and packaging material from the carton. Remove any staples from the bottom of the carton and then lift the carton up and off the unit.

2. The tiller is heavy and you should not attempt to remove it from the shipping platform until the handlebars are installed. The procedure for removing the tiller is explained in Step 3 of these assembly steps. NOTE: Be careful not to

severely bend any of the control cables on the unit.

3.Remove all unassembled parts and the separate hardware bag from the carton. Check that you have the items listed below (contact your local dealer or the factory if any items are missing or damaged). NOTE: Use the screw length template (Fig. 2-1) to identify screws.

Loose Parts List

Qty. Description

1Handlebar Support (see A, Fig. 2-2, page 7)

1Handlebar Assembly (see K, Fig. 2-2)

The following items are in the hardware bag:

1Slotted hd. screw, #10-24 x 2"

1Hex hd. screw, 1/4-20 x 1-1/4"

6Curved hd. screw, 5/16-18 x 1-1/2"

2Hex hd. screw, 3/8-16 x 3/4"

2Flat washer, 3/8"

6Split lockwasher, 5/16"

1Hex locknut, 1/4"-20

6Hex nut, 5/16"-18

2Hex locknut, 3/8"-16

1Hex nut, #10-24

1Spring, cable (see W, Fig. 2-5, page 8)

1Bracket, forward clutch cable (see P, Fig. 2-5, page 8)

1Bracket, reverse clutch cable (see BB, Fig. 2-8, page 9). (Not used on Model 12190.)

IMPORTANT: Motor oil must be added to the engine crankcase before the engine is started. Follow the instructions in this “Assembly” section.

NOTE: LEFT and RIGHT sides of the tiller are as viewed from the operator’s position behind the handlebars.

Tools/Materials Needed for Assembly

(1)3/8” open-end wrench*

(2)7/16" open-end wrench*

(1)1/2" open-end wrench*

(2)9/16" open-end wrench*

(1)Large adjustable wrench (not used with Model 12190)

(1) Scissors (to trim plastic ties)

(1) Ruler (for belt tension check)

(1)Block of wood (to support tiller when removing wheels)

(1) Automotive-type air pressure gauge

(1) Clean oil funnel

(1)Clean, high-quality engine oil. Refer to the Engine Owner Manual for engine oil specifications and quantity required. Do not overfill.

*Adjustable wrenches may be used.

1

2

3

Figure 2-1: To identify length of screw, place screw on template as shown and measure distance between bottom of screw head and tip of screw.

6

Page 6
Image 6
Troy-Bilt 12190-3HP Introduction, Inspect unit, Tools/Materials Needed for Assembly, Unpacking Instructions, Section