McCulloch 96041018001 manual Troubleshooting Points

Page 26

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

Engine continues

1.

Faulty operator-safety presence control

1.

Check wiring, switches and connections. If not

 

to run when oper-

 

system.

 

corrected, contact an authorized service center/

 

ator leaves seat

 

 

 

department.

 

 

 

 

 

 

with attachment

 

 

 

 

 

clutch engaged

 

 

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

 

2.

Mower deck not level.

2.

Level mower deck.

 

 

3.

Buildup of grass, leaves, trash under mower.

3.

Clean underside of mower housing.

 

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

 

5.

Clogged mower deck vent holes from

5.

Clean around mandrels to open vent holes.

 

 

 

buildup of grass, leaves, and trash around

 

 

 

 

 

mandrels.

 

 

 

Mower blades will

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

 

not rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

 

 

Poor grass

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

discharge

2.

Travel speed too fast.

2.

Shift to slower speed.

 

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

 

4.

Mower deck not level.

4.

Level mower deck.

 

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

 

6.

Worn, bent or loose blade.

6.

Replace blade. Tighten blade bolt.

 

 

7.

Buildup of grass, leaves, trash under mower.

7.

Clean underside of mower housing.

 

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

 

10.

Improper blades used.

10.

Replace with blades listed in parts manual.

 

 

11.

Clogged mower deck vent holes from buildup

11.

Clean around mandrels to open vent holes.

 

 

 

of grass, leaves, trash around mandrels.

 

 

 

Headlight(s) not

1.

Switch is “OFF”.

1.

Turn switch “ON”.

 

working

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

(if so equipped)

3.

Faulty light switch.

3.

Check/replace light switch.

 

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

 

 

Battery will not

1.

Bad battery cell(s).

1.

Replace battery.

 

charge

2.

Poor cable connections.

2.

Check/clean all connections.

 

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

 

 

Loss of drive

1.

Freewheel control in “disengaged” position.

1.

Place freewheel control in “engaged” position.

 

 

2.

Debris on steering plate (if equipped).

2.

See "CLEANING" in the maintenance section.

 

 

3.

Motion drive belt worn, damaged, or broken.

3.

Replace motion drive belt.

 

 

4.

Air trapped in transmission during

4.

Purge transmission.

 

 

 

shipment or servicing.

 

 

 

 

5.

Axle key missing.

5.

Install axle key at rear wheel. See "TO REMOVE

 

 

 

 

 

WHEEL" in the Service and Adjustments section.

 

 

 

 

 

 

 

Engine "back-

1.

Engine throttle control not set between

1.

Move throttle control between half and full speed

 

fires” when turn-

 

half and full speed (fast) position before

 

(fast) position before stopping engine.

 

 

stopping engine.

 

 

 

ing engine “OFF”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Engine dies when

1.

Reverse operation system (ROS) is not "ON"

1.

Turn ignition key to ROS "ON" position. See

 

tractor is shifted

 

while mower or other attachment is engaged.

 

Operation section.

 

into reverse

 

 

 

 

 

 

 

 

 

 

 

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents OPERATOR’S Manual General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering WheelTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Deck Levelness To Adjust Seat See FigCheck Tire Pressure Operation Position Know Your TractorROS on Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control See FigReverse Operation System ROS To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTowing Carts and Other Attachments Before Starting the EngineTo Operate on Hills Check Engine OIL LevelAutomatic Transmission Warm UP Mowing TipsPurge Transmission General Recommendations MaintenanceMaintenance ScheduleBlade Removal See Fig BatteryTractor Engine Deck Washout Port See Fig CleaningIN-LINE Fuel Filter See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transaxle Motion Control Lever Neutral Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionTroubleshooting Points Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX04.02.11 JA/TH

96041018001 specifications

The McCulloch 96041018001 is a highly regarded chainsaw designed for both professionals and tree care enthusiasts. Its robust performance and user-friendly features make it an ideal choice for tackling a variety of cutting tasks, whether it's trimming branches, felling trees, or cutting firewood.

One of the standout features of the McCulloch 96041018001 is its powerful gasoline engine. With a displacement of 40 cc, this engine generates sufficient power to handle demanding cutting jobs efficiently. The chainsaw boasts a maximum power output of approximately 1.5 kW, ensuring that it can tackle thick branches and trunks with ease. The engine is designed with efficient fuel consumption in mind, which not only saves operating costs but also reduces the environmental impact.

Equipped with a 14-inch guide bar, the McCulloch 96041018001 offers a perfect balance of reach and control. This length is ideal for a variety of applications, making it suitable for both light pruning and substantial cutting tasks. The chainsaw also features a chain brake system which provides added safety, preventing accidental kickback and ensuring user protection during operation.

An important aspect of the McCulloch 96041018001 is its Easy Start technology. This innovative feature allows for simpler starting with less effort, reducing the strain on the user and providing a quick readiness for work. Additionally, the chainsaw includes an automatic chain lubrication system that maintains optimal chain and bar performance, enhancing longevity and reducing wear during use.

The lightweight design of the McCulloch 96041018001 contributes to its ease of handling and maneuverability. Weighing in at just around 4.4 kg, operators can work longer without experiencing excessive fatigue, making it suitable for extended cutting sessions. Its ergonomic handle design adds to the overall comfort, ensuring a secure grip even in challenging conditions.

Moreover, the McCulloch 96041018001 features a tool-less chain tensioning system that allows users to adjust the chain tension quickly and easily, improving convenience and efficiency. Overall, this chainsaw strikes a commendable balance between power, safety, and ease of use, making it a valuable addition to any toolkit for those looking to tackle outdoor cutting tasks effectively.
Top Page Image Contents