McCulloch MC1538ST manual Tractor, Brake Operation, Tires, Operator Presence System, Blade Care

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than fi ve (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See“PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without fi rst setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 9)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and fl at washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS HEATTREATED.IF BOLT NEEDS REPLACING, REPLACE ONLY WITH APPROVE BOLT SHOWN IN THE REPAIR PARTS.

MANDREL

TRAILINGASSEMBLY EDGE UP

CENTER

HOLE

LOCK WASHER

STAR

FLAT WASHER

BLADE

 

BLADE BOLT

FIG. 9

TO SHARPEN BLADE (See Fig. 10)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a fi le or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT OR PIN

BLADE

FIG. 10

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model NO. MC1538ST MC1538STA II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationService III. ChildrenIV. Towing Table of Contents Steering Wheel Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonConnect Battery See Figs Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsMaintenance General RecommendationsBefore Each USE Operator Presence System TractorBrake Operation TiresEngine Spark Plugs CleaningClean AIR INTAKE/COOLING Areas MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing To Replace Mower Blade Drive Belt See FigBelt Removal To Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigBelt Installation To Adjust BrakeFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTo Adjust Throttle Control Cable To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points With attachment clutch Tractor - Model Number MC1538ST MC1538STA, Product no 77 SchematicElectrical KEY Part NO. NO. Description Chassis Repair Parts Drive Repair Parts Steering Repair Parts Optional Equipment EngineKEY Part NO. no Description SeatWheels & Tires DecalsMower Lift Mower Deck KEY Part Description Service Notes Service Notes Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

MC1538ST specifications

The McCulloch MC1538ST is a versatile and robust lawn mower designed for homeowners who seek performance combined with user-friendly features. This compact yet powerful mower is engineered to handle various mowing tasks effectively, making it a popular choice among gardening enthusiasts.

One of the standout features of the MC1538ST is its powerful 38cc engine. This engine provides ample power for cutting through thick grass and ensures reliable performance on different terrains. The durable steel cutting deck allows for a precise and clean cut, promoting a well-groomed lawn. The deck size of 38 cm makes it suitable for both small and medium-sized gardens, where maneuverability is crucial.

Another significant aspect of the MC1538ST is its unique cutting system. The mower comes with a three-in-one functionality; it can mulch, rear discharge, or collect grass clippings in a detachable bag. This versatility allows users to choose how they want to manage their grass clippings, enhancing the mowing experience while keeping the garden tidy.

The ergonomic design of the MC1538ST contributes to its ease of use. With a lightweight construction and comfortable handles, it is designed for effortless maneuverability. The mower features a foldable handle, making it easy to store in compact spaces. Moreover, the adjustable cutting height is another user-friendly feature, allowing for customization based on the grass type and desired length.

The MC1538ST adopts modern technology with its integrated safety features, including a safety switch that prevents unintended operation, enhancing user safety during mowing. The mower is also designed to minimize noise levels, providing a more pleasant mowing experience for both the user and any nearby neighbors.

In summary, the McCulloch MC1538ST is an excellent choice for those seeking a reliable and efficient lawn mower. With its powerful engine, versatile cutting options, and user-centric design, it streamlines the mowing process while ensuring an aesthetically pleasing lawn. Whether you’re a seasoned gardener or a novice, the MC1538ST will meet your lawn care needs with ease and efficiency.
Top Page Image Contents