Sears 917.25597 owner manual Tractor, Blade Care, Transaxle Cooling, Check Transaxle OIL Level

Page 16

CUSTOM ESPONSI L ES

TRACTOR

Always observe safety rules when performing any mainte- nance_

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted.. (See "TO ADJUST BRAKE" in the Service and Adjust- ments section of this manual).

TIRES

oMaintain proper air'pressure in all tires (See "PROD- UCT SPECIFICATIONS" on page 3 of this manual)_

*Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber..

oAvoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

BLADE CARE

Forbest results mower blades must be kept sharp. Replace bent or'damaged blades.

TO SHARPEN BLADE (See Fig. 15)

Care should be taken to keep the blade balanced_ An unbalanced blade will cause excessive vibration and even-

tual damage to mower and engine,

°The blade can be sharpened with a file or on a grinding wheel Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, ora cone balancer. (When using a cone balancer, follow the instructions supplied with bal- ancer)o

•Slide blade on to an unth readed portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced..

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

CENTER HOLE

BLADE REMOVAL (See Fig. 14)

oRaise mower to highest position to allow access to blades.

•Remove hex bott, tockwasherand flat washer securing blade.,

5/8" BOLT

OR PIN

BLADE

°Install new or'resharpened blade with trailing edge up towards deck as shown.

oReassemble hex bolt, lock washer and flat washer in exact order as shown.

°Tighten bolt securely (30-35Ft. Lbso torque)..

IMPORTANT: BLADE BOLT IS GRADE 8 HEATTREATED.

NOTE: We do not recomrnend sharpening blade- but if you do, be sure the blade is balanced.

MANDREL

BLADEASSEMBLY

FIG. 15

TRANSAXLE COOLING

Keep transaxle free from build-up of dirt and chaff which can restrict cooling..

CHECK TRANSAXLE OIL LEVEL

(See Fig. 16)

=Block up rear axle securely or use a tractor jack,

° Remove left rear wheel by removing hub bolts,,

°Remove filler plug from transaxle, Oil level must be even with plug threads, If necessary, fill with SAE 30 non-detergent oil (ISO 100), Replace filler plug,

TRAILING

EDGE UP

°Reassemble wheel to hub.

- Forapproximate capacity see "PRODUCT SPECIFI- CATIONS" on page 3 of this manual.

FLAT

WASHER,

._

/

LOCK

WASHER ,

_

/

O

TRANSAXLE

FILLER PLUG

o

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 14

O

0

16

FIG, 16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Ownersmanual Safe Operation Practices for Ride-On Mowers Ill ChildrenMaintenance Agreement Limited 90 DAY Warranty on BatteryElectric Start Rbding Equipment ModelLE of Contents Engine MaintenancePerformance IIllo \ J Tools Requured for Assembly To Remove Tractor from CartonBefore Rolling Tractor OFF Skid Unpack CartonHOW to SET UP Your Tractor Prepare Battery See FigInstall Seat See Fig Check Tire PressureCheck Deck Levelness Install Mower and Drive Belt SeeCheck for Proper Position of ALL Belts Checklist Install Battery See FigsOperation Know Your TractorHOW to USE Your Tractor To Adjust Mower Cutting HeightTo USE Throttle Control See Fig To Move Forward and Backward See FigTo Adjust Gauge Wheels See Fig To Operate on HillsTo Transport Before Starting the EngineADD Gasoline Mowing TipsGeneral Recommendations Lubrication ChartBefore Each USE Tractor Blade CareTransaxle Cooling Check Transaxle OIL LevelBattery See Fig To Clean Battery and TerminalsBelts LubricationCleaning Clean Engine Cooling FinsMuffler AIRTo Level Mower Housing To Install MowerTractor To Remove Mower See FigService To Replace Mower Drive BeltTo Adjust Brake See Fig To Adjust AttachmentTo Replace Mower Blade Drive Belt ClutchFront Wheel TOE-IN Adjustment See FigFront Wheel View from Left Side of TractorTo Start Engine with a Weak Battery To Adjust Attachment Lift SpringTo Replace Headlight Bulb INTERLOCKS and RelaysTo Adjust Throttle Control Cable EngineTo Adjust Carburetor Preliminary SettingFinal Setting See FigsEngine OtherBatery Engine OILRvic Notes Problem Cause CorrectionProblem Cause Correction TF Oubleshoot NG PohntsSchematic Insulated ClipsDecals Wheels & Tires8167 KEY Part DescriptionElectrocal Electrbcal PT.OChassis and Enclosures KEY Part NOwGround Drive 18 HP 44 Tractor28\ Locknut Steering Assembly Steering Assembly Engine VGT UNCKEY Part NO. no Seat Assembly124181X KEY Part NO. no Description Lift RhKEY PartMower Deck Description Mower DeckIdler Repaiir Parts TransaxleKEY Part KEY Part NO. noU.S. inches Briggs & Stratton Engine Model Number 422707, Type Number 3052o6 235 REPAIlR Parts Assembly Briggs & Stratton Engine Model Number 422707, Type NumberS44 783REPAnR Parts NO. noFuel Line to Tank MAGNETRON@Page Suggested Guide for Sighting Slopes for Safe Operatron Part Number = Model Number Engine Model no , Type noPart Description

917.25597 specifications

The Sears 917.25597 is a versatile and efficient lawn mower model that stands out for its reliability and ease of use. Designed for homeowners looking for a robust solution to maintain their lawns, it incorporates a range of features that enhance its performance and user experience.

One of the key features of the Sears 917.25597 is its powerful engine. Equipped with a reliable gas-powered engine, this mower provides ample power to tackle various types of grass and terrain. The engine's design ensures smooth operation, leading to a longer lifespan and less maintenance compared to smaller, less durable engines. This robust power source translates into efficient cutting, allowing users to complete their lawn-mowing chores quickly and effectively.

The cutting deck of the Sears 917.25597 is another standout feature. With a wide cutting width, typically around 21 inches, it allows for broader mowing paths, reducing the time and effort you need to spend on your lawn. The deck is made from high-quality materials designed for durability. Additionally, the mower usually features adjustable cutting height settings, allowing users to customize grass length easily according to their preferences or seasonal needs.

Another technological advancement in the Sears 917.25597 is its self-propulsion system. This feature enables the mower to move forward with minimal effort from the user, making it ideal for larger properties. The self-propelled mechanism adjusts according to your walking speed, providing a comfortable mowing experience without requiring significant physical exertion.

User-friendly design is evident throughout the mower’s structure. The handle is adjustable, ensuring comfort for users of varying heights. The easy-start ignition system takes the hassle out of traditional pull-starts, allowing for a quick and reliable startup every time.

The Sears 917.25597 also considers storage and maintenance. Many models come with a foldable handle for easy storage in garages or sheds. Additionally, its components are designed for straightforward access, making routine maintenance tasks such as oil changes and air filter replacements uncomplicated.

In summary, the Sears 917.25597 is a well-rounded lawn mower that delivers reliable power, efficient cutting capabilities, and user-friendly features. Its blend of durability and performance makes it a suitable choice for homeowners looking to maintain an attractive lawn with minimal hassle.
Top Page Image Contents