Sears 917.25597 See Fig, Front Wheel TOE-IN Adjustment, View from Left Side of Tractor

Page 22

SERVICE AN ADJUSTMENTS

TO REPLACE MOTION DRIVE BELT

(See Fig. 31)

Park the tractor on level surface_ Engage parking brake. For ease of service there is a belt installation guide decal on bottom of left footrest. It is not necessaryto remove mower.

BELT REMOVAL -

•Raise hood and disconnect BLACK (grounding) bat- tery cable..

°Set parking brake (to get belt slack)_

°Remove mower'drive belt from electric clutch pulley only (See "TO REPLACE MOWER DRIVE BELT" in this section of this manual).

°Roll belt off transaxle pulley.

•Roll belt Off clutching idler pulleys, then off engine pulley and front V-idler pulley°

•Pull belt out of all beltkeepers.

BELT INSTALLATION -

°Place V part of belt into grooves on engine pulley and front V-idler, making sure to route belt inside of beitkeepers..

°Put belt coming fromV-idler above midspan beltkeeper, then onto clutching idler pulleys as shown.

•Make sure "V" part of belt engages "V" idler._

=Place belt around transaxle pulley, beginning at top._ "V" part of belt should engage transaxle pulley.

°Place long lower section of belt through loop in midspan beltkeepero

,Checkto be sure belt is on proper side of all beltkeeper&

=Release parking brake..

IMPORTANT: CHECK BRAKE ADJUSTMENT..

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer-

ing wheel and reassemble per instructions in the Assembly section of this manual.,

FRONT WHEEL TOE-IN ADJUSTMENT

Front wheel toe-in is required for proper steering operatiorL Toe-in was set at the factory and adjustment should not be necessary.. If parts in the front axle or-steering mechanism have been replaced or damaged, check to-in and adjust if necessary_

TO CHECK TOE-IN (See Fig_ 32) -

°Position front wheels straight ahead_

-Measure distance between wheels at front and rear of tires (dimensions "A" and "B").

=Front dimension "A" should be 1/8" to 1/4" less than rear'dimension "B"_.

TO ADJUST TOE-IN (See Figs° 32 and 33) -

°Loosen jam nuts at adjustment sleeves on tie rod.

-Adjust tie rod until dimension "A" is 1/8" to 1/4" less than dimension "B",.

°Tighten jam nuts securely.

.., B .,-

FRONT OF TRACTOR

 

A_

ABOVE

CLUCHING

FIG. 32

ENGINE KEEPER

CLUCHINP.-., \ V -IDLER

FLATIDLER _

ADJUSTMENT SLEEVES

I

BELT

TWISTS

TRANSAXLE

 

 

JAM NUTS

 

 

 

 

 

 

 

 

 

PULLEY

 

 

 

 

 

 

 

 

 

 

FIG. 33

 

 

AS VIEWED FROM BOTTOM

i

FRONT

WHEEL

CAMBER

 

 

Jl.,llllll

 

 

TRACTOR V-BELTDRIVE SCHEMATIC

The front wheel camber-is not adjustable

on your tractor. If

VIEW FROM LEFT SIDE OF TRACTOR

damage

has occurred to affect

the front wheel camber,

 

contact your nearest

authorized

service

center..

FIG. 31

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Ownersmanual Safe Operation Practices for Ride-On Mowers Ill ChildrenElectric Start Rbding Equipment Maintenance AgreementLimited 90 DAY Warranty on Battery ModelLE of Contents Engine MaintenancePerformance IIllo \ J Before Rolling Tractor OFF Skid Tools Requured for AssemblyTo Remove Tractor from Carton Unpack CartonInstall Seat See Fig HOW to SET UP Your TractorPrepare Battery See Fig Check Tire PressureCheck Deck Levelness Install Mower and Drive Belt SeeCheck for Proper Position of ALL Belts Checklist Install Battery See FigsOperation Know Your TractorTo USE Throttle Control See Fig HOW to USE Your TractorTo Adjust Mower Cutting Height To Move Forward and Backward See FigTo Transport To Adjust Gauge Wheels See FigTo Operate on Hills Before Starting the EngineADD Gasoline Mowing TipsGeneral Recommendations Lubrication ChartBefore Each USE Transaxle Cooling TractorBlade Care Check Transaxle OIL LevelBelts Battery See FigTo Clean Battery and Terminals LubricationMuffler CleaningClean Engine Cooling Fins AIRTractor To Level Mower HousingTo Install Mower To Remove Mower See FigService To Replace Mower Drive BeltTo Replace Mower Blade Drive Belt To Adjust Brake See FigTo Adjust Attachment ClutchFront Wheel Front Wheel TOE-IN AdjustmentSee Fig View from Left Side of TractorTo Replace Headlight Bulb To Start Engine with a Weak BatteryTo Adjust Attachment Lift Spring INTERLOCKS and RelaysTo Adjust Throttle Control Cable EngineFinal Setting To Adjust CarburetorPreliminary Setting See FigsBatery EngineOther Engine OILRvic Notes Problem Cause CorrectionProblem Cause Correction TF Oubleshoot NG PohntsSchematic Insulated Clips8167 DecalsWheels & Tires KEY Part DescriptionElectrocal Electrbcal PT.OChassis and Enclosures KEY Part NOwGround Drive 18 HP 44 Tractor28\ Locknut Steering Assembly Steering Assembly Engine VGT UNCKEY Part NO. no Seat Assembly124181X KEY KEY Part NO. no DescriptionLift Rh PartMower Deck Description Mower DeckIdler Repaiir Parts TransaxleKEY Part KEY Part NO. noU.S. inches Briggs & Stratton Engine Model Number 422707, Type Number 3052o6 235 REPAIlR Parts S44 AssemblyBriggs & Stratton Engine Model Number 422707, Type Number 783REPAnR Parts NO. noFuel Line to Tank MAGNETRON@Page Suggested Guide for Sighting Slopes for Safe Operatron Part Number = Model Number Engine Model no , Type noPart Description

917.25597 specifications

The Sears 917.25597 is a versatile and efficient lawn mower model that stands out for its reliability and ease of use. Designed for homeowners looking for a robust solution to maintain their lawns, it incorporates a range of features that enhance its performance and user experience.

One of the key features of the Sears 917.25597 is its powerful engine. Equipped with a reliable gas-powered engine, this mower provides ample power to tackle various types of grass and terrain. The engine's design ensures smooth operation, leading to a longer lifespan and less maintenance compared to smaller, less durable engines. This robust power source translates into efficient cutting, allowing users to complete their lawn-mowing chores quickly and effectively.

The cutting deck of the Sears 917.25597 is another standout feature. With a wide cutting width, typically around 21 inches, it allows for broader mowing paths, reducing the time and effort you need to spend on your lawn. The deck is made from high-quality materials designed for durability. Additionally, the mower usually features adjustable cutting height settings, allowing users to customize grass length easily according to their preferences or seasonal needs.

Another technological advancement in the Sears 917.25597 is its self-propulsion system. This feature enables the mower to move forward with minimal effort from the user, making it ideal for larger properties. The self-propelled mechanism adjusts according to your walking speed, providing a comfortable mowing experience without requiring significant physical exertion.

User-friendly design is evident throughout the mower’s structure. The handle is adjustable, ensuring comfort for users of varying heights. The easy-start ignition system takes the hassle out of traditional pull-starts, allowing for a quick and reliable startup every time.

The Sears 917.25597 also considers storage and maintenance. Many models come with a foldable handle for easy storage in garages or sheds. Additionally, its components are designed for straightforward access, making routine maintenance tasks such as oil changes and air filter replacements uncomplicated.

In summary, the Sears 917.25597 is a well-rounded lawn mower that delivers reliable power, efficient cutting capabilities, and user-friendly features. Its blend of durability and performance makes it a suitable choice for homeowners looking to maintain an attractive lawn with minimal hassle.
Top Page Image Contents