Weed Eater 530088776 Attaching the Control Handle to the Handlebar, Assembly of Shoulder Strap

Page 5

S Insert screws and hand tighten only. These

screws will be tightened later.

Bracket Cover

 

 

 

 

 

 

Screw

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mounting

 

 

 

 

 

Handlebar

 

 

 

 

 

 

 

 

 

 

 

Bracket

 

 

 

 

 

 

 

ATTACHING THE CONTROL HANDLE TO THE HANDLEBAR

NOTE: Make sure the wire going to the con- trol handle is routed below the tube and re- mains on the right side of the handlebar and the tube.

Screw

Screw Hole

SSlide handle onto the right side of the han- dlebar and align the screw hole.

SInsert screw and tighten securely. NOTE: Make sure the control handle is on the right side of the unit as shown in the il- lustration below, and the ON/OFF switch is lo- cated on the top of the control handle.

S Adjust the handlebar to the proper position and tighten the two screws you left loose during handlebar assembly. Make sure these screws are securely tightened.

S After attaching the control handle and tight- ening the handlebar, route the wire from the control handle through the slit in the bottom of the foam grip.

Foam Grip

Slit Wire

ASSEMBLY OF SHOULDER STRAP

WARNING: Proper shoulder strap and handlebar adjustments before starting the en- gine are required.

STry on shoulder strap and adjust for fit and bal- ance before starting the engine or beginning a

cutting operation.

SInsert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right side of your waist.

NOTE: A one-half twist is built in the shoulder strap to allow the strap to rest flat on the shoul- der.

S Adjust the strap, allowing the hook to be about 6 inches below the waist.

SFasten the strap hook to the clamp located between the foam grip and the mounting block and lift the tool to the operating posi- tion.

CONFIGURING YOUR UNIT

You can configure your unit using a cutting head for grass and light weeds, or a brush blade for cutting saplings and similar size ma- terial. Go to the section for the desired configuration and follow the instructions for assembling your unit.

ASSEMBLY INFORMATION -

TRIMMER HEAD

TRIMMER

HEAD

NOTE: Remove the blade and metal shield before attaching the plastic shield and trimmer head. To remove blade, push in locking lever and hold. Rotate blade nut until the locking le- ver falls into one of the grooves in the dust cup. Continue to hold the locking lever. This will keep the shaft from turning while loosening the blade nut. Remove blade nut by turning clock- wise. Release locking lever. Remove both washers and blade. To remove metal shield, loosen and remove the four mounting screws. See ATTACHING THE METAL SHIELD and INSTALLING THE METAL BLADE for illustra- tions. Be sure to store all parts and instruc- tions for future use.

ATTACHING THE PLASTIC SHIELD AND TRIMMER HEAD

WARNING: The shield must be prop- erly installed. The shield provides partial protec- tion from the risk of thrown objects to the opera- tor and others and is equipped with a line limiter which cuts excess line to the proper length. The line limiter (on underside of shield) is sharp and can cut you.

SRemove wing nut from shield.

SInsert bracket into slot on shield.

SPivot shield until bolt passes through hole in bracket.

STighten the wing nut securely.

SIf your unit has a plastic cover over the threads on the threaded shaft, remove the covering to expose the threads.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents URL Protection Operator SafetyEye Fuel Safety UNIT/MAINTENANCE SafetyCutting Safety Transporting and StorageAssembly Tools Required Carton ContentsAttaching the Tube Attaching the HandlebarConfiguring Your Unit Assembly of Shoulder StrapAssembly Information Trimmer Head Attaching the Control Handle to the HandlebarAssembly of the Metal Shield Assembly Information Brush BladeInstallation of the Metal Blade Top view of blade Teeth on blade point in this directionSwitch HOW to Stop Your UnitStarting Your Engine Throttle TriggerOperating Position Starting a Warm EngineOperating Instructions for USE with Trimmer Head Advancing the Trimmer LineReplacing the Line Blade spins increases the cutting actionTroubleshooting Table Cause Remedy Carburetor AdjustmentSpark Plug Ignition TimingProducts are pleased to explain Center. If you have any questions regardingMaintenance, or which is scheduled only for Scheduled for replacement as requiredFor replacement as required maintenance Replacement part used in the performance

530088776 specifications

The Weed Eater 530088776 is a powerful and reliable string trimmer designed to help homeowners and professionals maintain their lawns and gardens with ease. Known for its user-friendly features and efficient operations, this model stands out in the crowded market of outdoor power equipment.

One of the main features of the Weed Eater 530088776 is its robust engine, which delivers ample power to tackle overgrown grass and weeds. The two-cycle engine is designed for optimal performance, providing the necessary torque and speed for effective trimming. It is lightweight, making it ideal for extended use without causing fatigue.

Another noteworthy characteristic is the trimmer's rapid reload head. This feature simplifies the process of changing the cutting line, allowing users to quickly load new line without the need for additional tools. This convenience not only saves time but also enhances the user experience, especially for those who frequently use the trimmer.

The Weed Eater 530088776 also incorporates a straight shaft design, which offers better reach and maneuverability, particularly in tight spaces and underbrush. The straight shaft allows users to trim grass and weeds in hard-to-reach areas without straining their backs. This ergonomically designed trimmer is equipped with a comfortable grip, ensuring a secure hold during operation.

In terms of technology, the Weed Eater 530088776 features an anti-vibration system that minimizes user fatigue during extended lawn care sessions. This advanced technology dampens the vibrations produced by the engine, providing a more comfortable trimming experience. Additionally, its lightweight construction enhances portability, making it easy to transport around the yard.

The trimmer is designed with durability in mind, featuring high-quality materials that withstand the rigors of outdoor use. Its efficient fuel consumption also plays a significant role in reducing emissions, making it an environmentally friendly choice for users concerned about their carbon footprint.

In summary, the Weed Eater 530088776 is a versatile and efficient string trimmer that delivers powerful performance for all your yard maintenance needs. With its user-friendly features, ergonomic design, and advanced technologies, it is a valuable addition to any outdoor toolkit, whether for casual homeowners or professional landscapers.
Top Page Image Contents