HOW to Start Your Unit, Operating Position

Engine Choke Lever

ON/STOP

Switch

FULL HALF OFF

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move choke lever to the FULL CHOKE posi- tion.

4.Squeeze the throttle trigger fully and hold through all remaining steps.

Starter Handle

Choke

Lever

flooded. Proceed to STARTING A FLOODED ENGINE.

8.Once the engine starts, allow it to run 10 seconds, then move the choke lever to the OFF CHOKE position. Allow the unit to run for 30 more seconds at OFF CHOKE be- fore releasing the throttle trigger.

NOTE: If engine dies with the choke lever in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move the choke lever to the HALF CHOKE position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the engine runs smoothly.

3.Pull starter rope sharply until engine runs, but no more than 5 pulls.

4.Allow engine to run 15 seconds, then move the choke lever to OFF CHOKE.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex- cess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded.

If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING INSTRUCTIONS

It is recommended that the engine not be operated for longer than 1 minute at full throttle.

OPERATING POSITION

ALWAYS WEAR:

Eye Protection

Muffler

Long Pants

Primer Bulb

Heavy Shoes

5.Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

6.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

7.Pull starter rope sharply until engine runs, but no more than 6 pulls.

NOTE: If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE posi- tion and pull the starter rope until the en- gine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably

Cut from your right to your left.

WARNING: Always wear eye protec- tion. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury.

Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to “weld” onto the spool.

Always release the throttle trigger and allow the engine to return to idle speed when not cutting.

530163364 specifications

The Weed Eater 530163364 is an innovative and high-performance string trimmer designed to tackle various lawn care tasks with ease and efficiency. This model stands out in its class due to its advanced features, robust construction, and user-friendly design, making it a popular choice for both homeowners and landscaping professionals.

One of the most notable features of the Weed Eater 530163364 is its powerful engine. With a reliable two-stroke engine, this trimmer delivers consistent power to handle thick grass, weeds, and even light brush. The engine is designed for easy starting, reducing the frustration often associated with starting traditional gas-powered outdoor equipment.

In terms of technology, the Weed Eater 530163364 incorporates a bump feed head system that ensures uninterrupted operation. When the string wears down, users can simply tap the trimmer head against the ground to release more line, eliminating the need to stop and manually adjust the cutting line. This feature significantly enhances productivity, allowing you to complete your trimming tasks more efficiently.

Another key characteristic of this trimmer is its lightweight design. Weighing in at just under 10 pounds, the Weed Eater 530163364 is easy to maneuver around gardens, flower beds, and other tricky spots. The adjustable handle provides better ergonomics and comfort, making it easy to operate for extended periods without causing undue strain on the user.

The cutting width of the Weed Eater 530163364 is 17 inches, making it versatile enough to handle small to medium-sized lawns effectively. The dual-line cutting system enables a cleaner cut and quicker trimming while ensuring precision in finishing edges and around obstacles.

Additionally, the Weed Eater 530163364 is designed for durability. The materials used in its construction are chosen for their resistance to impact and weather conditions, ensuring that this machine can withstand the rigors of outdoor use. The trimmer also comes with a safety guard to protect the user from debris while operating.

In summary, the Weed Eater 530163364 is a reliable and efficient tool for anyone looking to maintain their lawn or garden. With its powerful engine, innovative bump feed head, lightweight design, and durable construction, it combines performance and ease of use. Whether you are a professional landscaper or a homeowner tackling yard work, this trimmer is an exceptional choice that delivers excellent results.