Carburetor Adjustment, Seasonal Storage

Line in Notch

Hub	Line exit hole

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrow found on the spool.

6.Push the line into the notche, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the line into the the exit holebin the hub as shown in the illustration.

8.Align the notch with the line exit hole.

9.Push spool into hub until it snaps into place. 10.Pull the line extending outside of the hub to

release it from the notch.

CARBURETOR ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head will be spinning during this procedure. Wear your protective equipment and observe all safety precautions.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is re- leased.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making ad- justments. Keep all parts of your body away from the cutting attachment and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until engine runs without stalling (idle speed too slow).

S Turn idle speed screw clockwise to in- crease engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed.

Idle Speed

Screw

Air Filter

Cover

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

WARNING: Perform the following steps after each use:

S Allow engine to cool, and secure the unit before storing or transporting.

SStore unit and fuel in a well ventilated area

where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore unit with all guards in place. Position unit so that any sharp object cannot acci-

dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

SClean the entire unit before lengthy storage. S Store in a clean dry area.

S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol- low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom-

mended type and heat range.

SClean air filter.

S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

S At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

SDo not store gasoline from one season to

another.

SReplace your gasoline can if it starts to rust.

530163364 specifications

The Weed Eater 530163364 is an innovative and high-performance string trimmer designed to tackle various lawn care tasks with ease and efficiency. This model stands out in its class due to its advanced features, robust construction, and user-friendly design, making it a popular choice for both homeowners and landscaping professionals.

One of the most notable features of the Weed Eater 530163364 is its powerful engine. With a reliable two-stroke engine, this trimmer delivers consistent power to handle thick grass, weeds, and even light brush. The engine is designed for easy starting, reducing the frustration often associated with starting traditional gas-powered outdoor equipment.

In terms of technology, the Weed Eater 530163364 incorporates a bump feed head system that ensures uninterrupted operation. When the string wears down, users can simply tap the trimmer head against the ground to release more line, eliminating the need to stop and manually adjust the cutting line. This feature significantly enhances productivity, allowing you to complete your trimming tasks more efficiently.

Another key characteristic of this trimmer is its lightweight design. Weighing in at just under 10 pounds, the Weed Eater 530163364 is easy to maneuver around gardens, flower beds, and other tricky spots. The adjustable handle provides better ergonomics and comfort, making it easy to operate for extended periods without causing undue strain on the user.

The cutting width of the Weed Eater 530163364 is 17 inches, making it versatile enough to handle small to medium-sized lawns effectively. The dual-line cutting system enables a cleaner cut and quicker trimming while ensuring precision in finishing edges and around obstacles.

Additionally, the Weed Eater 530163364 is designed for durability. The materials used in its construction are chosen for their resistance to impact and weather conditions, ensuring that this machine can withstand the rigors of outdoor use. The trimmer also comes with a safety guard to protect the user from debris while operating.

In summary, the Weed Eater 530163364 is a reliable and efficient tool for anyone looking to maintain their lawn or garden. With its powerful engine, innovative bump feed head, lightweight design, and durable construction, it combines performance and ease of use. Whether you are a professional landscaper or a homeowner tackling yard work, this trimmer is an exceptional choice that delivers excellent results.