Troy-Bilt 20207 manual Operation Section, HOW to USE Pressure, To Start Pressure Washer

Page 9

Operation Section

4

HOW TO USE PRESSURE

6. Attach nozzle extension to spray gun (Figure 7).

 

 

Tighten by hand.

WASHER

If you have any problems operating your pressure washer, please call the pressure washer helpline at

1-888-611-6708.

To Start Pressure Washer

To start your pressure washer for the first time, follow these instructions step-by-step.This starting information also applies if you have let the pressure washer sit idle for at least a day.

1.Place pressure washer near an outside water source capable of supplying water at a flow rate greater than 3.0 gallons per minute and no less than 20 PSI at pressure washer end of garden hose.

2.Check that high pressure hose is tightly connected to spray gun and pump. See “Preparing Pressure Washer For Use” for illustrations.

3.Make sure unit is in a level position.

4.Connect garden hose to water inlet on pressure washer pump. Turn ON water.

CAUTION

DO NOT run the pump without the water supply connected and turned on.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

5.Squeeze trigger on gun until you have a steady stream of water.This purges the pump of air and impurities.

Figure 7 — Connect Nozzle Extension to Spray Gun

7.Position nozzle in low pressure mode (slide nozzle forward) and squeeze trigger on spray gun to relieve pressure caused by turning ON water.Water will flow out of gun in a thin stream. Continue to hold trigger until there is a steady stream of water and no air remains in system. Release trigger.

8.Engage safety latch to spray gun trigger (Figure 8).

Figure 8 — Spray Gun with Safety Latch Engaged

Safety Latch

9.Start engine according to instructions given in engine owner’s manual. Also see operating instructions tag located on the pressure washer.

CAUTION

Avoid injury from kickback.

•When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

•If engine starts and fails to continue to run or if increased resistance is felt during starting pull attempts, squeeze trigger on spray gun.

NOTE: Always keep the throttle lever in the “Fast” position when operating the pressure washer.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Manual No GS Revision 2 05/05/2004 Questions? Preguntas? Helpline 1-888-611-6708 M-F8-5 CTTable of Contents Safety RulesEquipment Description When Transporting or Repairing Equipment High pressure spray may damage fragile items including glass Know Your Pressure Washer Features and Controls SectionSiphon/Filter High Pressure OutletAssembly AssemblyPreparing Pressure Washer for USE Add Engine Oil and Fuel Connect Hose and Water Supply to PumpConnect High Connect Garden Hose to Water Inlet Checklist Before Starting EngineOperation Section HOW to USE PressureWasher To Start Pressure WasherHow to Use Adjustable Nozzle How to Stop Pressure WasherOperation Squeeze trigger on spray gun to relieve pressure in hosePressure Washer Rinsing Applying Detergent with the Adjustable NozzleAutomatic Cool Down System Thermal ReliefSection Maintenance General Maintenance RecommendationsPressure Washer Maintenance Maintenance Nozzle MaintenancePurge Pump of Air Contaminants Ring Maintenance Engine MaintenancePump Maintenance Data PlateStorage Always wear eye protection when using PumpSaverPreparing the Unit for Storage Storing the EngineTroubleshooting TroubleshootingProblem Cause Correction Page Exploded View and Parts List Unit Section Exploded Views and Parts ListsWAND,Adjustable Nozzle DescriptionExploded Views and Parts Lists Exploded View and Parts List PumpInclude all parts shown within the box Tabla DE Contenidos Reglas de SeguridadDescripción DEL Equipo Reglas DE SeguridadPeligro Sección 1 Reglas de SeguridadPrecaución Conozca SU Maquina Lavadora DE Presion Características y ControlesFiltro de Aire Boquilla Ajustable Perilla del Cebador Usada para arranque de motores fríosMontaje MontajePreparando EL Lavador a Presión Para SU USO Agregar Aceite al Motor y Gasolina Sección 3 MontajeConecte la Manguera y el Suministro de Agua a la Bomba Gancho del Pistola MangueraLista de Revision Previa al Arranque del Motor Cómo Usar SU Máquina Lavadora a Presión OperaciónCómo Darle Arranque a su Máquina Lavadora a Presión Cómo Detener su Máquina Lavadora a PresiónCómo Usar la Boquilla Ajustable Sección 4 OperaciónAplicación del Detergente Usando la Boquilla Ajustable Para aplicar el detergente, siga los siguientes pasosEnjuage de la Máquina Lavadora a Presión Sistema de Enfriamiento Automático Alivio TérmicoPara Enjuage Mantenimiento Recomendaciones GeneralesMantenimiento DE LA Maquina Lavadora a Presion Elimine el Aire y los Contaminantes de la Bomba Sección 5 MantenimientoMantenimiento de la Boquilla Mantenimiento de los Anillos OMantenimiento de la Bomba Mantenimiento DEL MotorPlaca de Características Cambio del aceite de la bombaPreparando LA Unidad Para SU Almacenamiento AlmacenamientoAlmacenando EL Motor Proteger la BombaDiagnosticos DE Averías Diagnosticos de AveríasEquipo Para Uso Del Consumidor Para Uso Comercial Efectiva desde el 12 ro de NoviembreGenerador Portátil AñoAbout your equipment warranty TROY-BILT Owner Warranty Policy Effective November 12Equipment Consumer Use Commercial Use Portable Generator Years 2nd year parts only

20207 specifications

The Troy-Bilt 20207 is a versatile and powerful outdoor tool designed to make yard care tasks more efficient and enjoyable. This machine is primarily recognized as a self-propelled lawn mower that combines performance with user-friendly features, making it suitable for both novice and experienced gardeners alike.

One of the standout features of the Troy-Bilt 20207 is its robust engine. Equipped with a dependable 159cc OHV engine, this mower provides reliable power and performance. The engine is designed for easy starting, ensuring that users can fire up their mower with minimal effort. This is particularly beneficial during early morning or rainy day mowing sessions when you simply want to get the job done quickly.

The 20207 model also includes a self-propelled feature, which significantly reduces the physical effort required to navigate through various terrains. With variable-speed transmission, users have the flexibility to adjust the pace according to their preference or the type of grass they're mowing. This adaptability ensures that tackling hilly areas or uneven patches becomes less strenuous.

Mowing height adjustment is another highlight of the Troy-Bilt 20207. This feature allows users to select their desired cutting height from six different positions, ranging from 1.25 inches to 3.75 inches. This capability ensures that you can maintain the perfect length for your specific lawn type, promoting healthy grass growth.

In terms of cutting deck design, the Troy-Bilt 20207 features a 21-inch steel deck that delivers a clean and precise cut. Its three-in-one functionality offers versatility, allowing users to choose between side discharge, mulch, or bagging grass clippings. The mulching option is particularly advantageous for those looking to return nutrients to their lawn, enhancing its overall health.

Ease of use is further enhanced with the mower’s adjustable handles, providing a comfortable grip for users of varying heights. The Troy-Bilt 20207 also includes larger rear wheels that improve maneuverability, especially in tight corners and around flower beds.

Built with durability in mind, the mower's premium materials and thoughtful design contribute to a long lifespan, making it a worthwhile investment for any homeowner. Overall, the Troy-Bilt 20207 is a powerhouse in the realm of lawn care, combining advanced technology, performance, and user-friendly features to create a machine that exceeds expectations in maintaining a pristine lawn.
Top Page Image Contents