Troy-Bilt 52065 owner manual Operating the Machine, Using the Trimmer Head Control Bail

Page 10

10Section 4: Operation

USE THE CORRECT DIAMETER TRIMMER LINE

Before starting a project, look at the grass or material you will be cutting.

For tougher conditions, use two (or four) sections of the thicker gauge, .155" diame- ter extra-heavy duty line. For less demanding conditions, use two sections of the thinner gauge, .130" diameter heavy-duty line. The thicker line has the heft to chop through tougher materials, while the thinner line provides a more pre- cise cut. To change trimmer lines, refer to “Changing Trimmer Lines” in Section 5.

NOTE: The thinner line is also recom- mended for use near trees or ornamentals to help prevent girdling (cutting the bark).

A

Figure 4-3: Control bail.

OPERATING THE MACHINE

Once you have read and understood the sections in this Manual on “Safety,” “Assembly,” “Features and Controls,” and “Operation,” you are ready to operate your machine.

TO START THE TRIMMER HEAD

1.Stand in the operator’s position directly behind the handlebars.

2.Slowly close the Trimmer Head Control Bail (Figure 4-3) against the handlebars to activate the trimmer head. Use the Engine Throttle Control Lever to adjust the speed of the trimmer head.

3.Once the trimmer head is revolving, push the unit along the path to be cut.

TO STOP THE TRIMMER HEAD

Let go of the Trimmer Head Control Bail. The bail will return to its open position and the trimmer head will stop turning.

TO STOP THE ENGINE

USING THE TRIMMER

HEAD CONTROL BAIL

Before starting the engine, know how to use the Trimmer Head Control Bail.

1.The Trimmer Head Control Bail (A, Figure 4-3) is used to start and stop trim- mer head rotation.

2.When starting the engine, always have the control bail in the disengaged (released) position to prevent the trimmer head from turning when the engine starts.

3.When the engine is running, pull the control bail up against the handlebar to start rotation of the trimmer head.

4.Let go of the control bail to stop the trimmer head. The control bail should spring forward to the disengaged position. If it doesn’t, do not use the machine until the control bail has been repaired.

WARNING

If the trimmer head control bail is not operating properly, shut off the engine, disconnect the spark plug wire and move the wire away from the plug.

Adjust or repair the control bail before using the trimmer/mower.

Failure to follow this instruction could result in personal injury or property damage.

CHECKLIST BEFORE STARTING

1.Complete the “Pre-Start Checklist” in this Section. You must wear safety glasses or goggles.

2.Check the trimmer line cutting height (see “Adjust Line Cutting Height” in this Section.

STARTING THE ENGINE

1.Move the unit to the work area.

2.Connect the spark plug wire to the spark plug.

3.Put on safety-approved eye protection.

4.Release (disengage) the Trimmer Head Control Bail (A, Figure 4-3).

5.Start the engine:

a)Put Engine Throttle Control Lever in FAST (rabbit symbol) position.

b)Push in fuel primer button as instructed in Engine Owner’s Manual. NOTE: Do not use primer to restart a warm engine after a short shutdown.

c)Pull recoil start rope slowly until resistance is felt. Then pull rope out rapidly to start engine. Let rope back in slowly. NOTE: If engine fails to start after three pulls, repeat steps b and c.

Put the Engine Throttle Control Lever in the STOP position. (If time allows, first move the throttle lever to the SLOW set- ting before stopping the engine.)

NOTE: If the unit is operated in a stationary position with the wear cup in contact with dry vegetation, significant heat will result that may deform the plastic spindle or scorch the vegetation.

WARNING

THROWN OBJECT HAZARD!

•Objects such as rocks, pebbles, and small debris will be thrown violently by the cutting head, resulting in significant hazard to eyes and exposed body parts.

•Always wear safety-approved eye protection and suitable clothing and footwear.

•Keep children, pets and bystanders 50 feet away from machine while operating.

•Be alert to hidden obstacles.

Failure to comply could result in injury or property damage.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Trimmer/Mower Table of Contents Safety General OperationChildren ServiceSlope Operation Do notHandlebar Safety DecalsOn right Handlebar On right side, rear Mower deck Assembly Steps AssemblyIntroduction Assembly Features and Controls Features and ControlsRecoil starter G, -1 is used to pull start the engine Adjust Line Cutting Height PRE-START ChecklistAdjust Handlebar Height OperationUsing the Trimmer Head Control Bail Operating the MachineOperating Tips & Techniques Materials to the right sideAdjusting Trimmer Head Engagement MaintenanceMaintenance Schedule To Adjust Belt TensionInspecting and Replacing the Drive Belt Belt ReplacementBelt Inspection Cleaning the Engine Belt Performance TroubleshootingLubrication General Engine Maintenance TRIMMER/MOWER Cleaning and Debris RemovalCompact Storage To Change Trimmer Lines Trimmer lines can be changedTroubleshooting Problem Possible Cause CorrectionDrawing no Ref. # Description Ref. # Description QtyParts List Parts List Drawing no 715 133 Accessories and Kits Engine Service and Repair Warranty ServiceReplacement Parts Owner Registration Card

52065 specifications

The Troy-Bilt 52065 is a robust and versatile tiller designed for gardening enthusiasts and professional landscapers alike. Known for its durable construction and innovative features, this machine is engineered to make soil preparation more effortless and efficient.

At the heart of the Troy-Bilt 52065 is its powerful engine, which typically boasts around 160 cc, ensuring ample power for breaking up compacted soil and tackling tough gardening tasks. The tiller is equipped with a 12-inch steel tines that are capable of tilling a width of 16 inches, making it suitable for both large and small gardens. The tines are designed for optimal performance, allowing for efficient weed control and soil aeration.

One of the standout features of the Troy-Bilt 52065 is its adjustable handle. This allows users of different heights to operate the tiller comfortably. Additionally, the handle can be folded down for easy storage, making it a practical choice for those with limited garage space.

This tiller also incorporates Troy-Bilt's patented "Forward and Reverse" tilling capability. This feature provides users with added maneuverability, enabling them to till tough soil in both directions. It significantly reduces the time spent on the job, allowing for a smoother tilling experience.

Another noteworthy characteristic of the Troy-Bilt 52065 is its easy-to-use controls. The intuitive throttle control and gear shift are conveniently located, allowing the operator to adjust speed and power without difficulty. This usability is a key selling point for both novice and experienced gardeners.

The machine's construction is solid, featuring a heavy-duty steel frame that can withstand the rigors of frequent use. Its wheels are designed for enhanced traction, making it easier to navigate various terrain types. With maintenance in mind, the Troy-Bilt 52065 is designed for straightforward access to components, ensuring that routine maintenance is an uncomplicated task.

In conclusion, the Troy-Bilt 52065 is an exceptional tiller that excels in performance, durability, and ease of use. Its blend of powerful features, innovative technology, and ergonomic design makes this tiller a valuable addition to any gardening toolkit. Whether preparing a new bed for planting or maintaining an existing garden, the Troy-Bilt 52065 delivers reliability and efficiency, making gardening tasks enjoyable rather than laborious.
Top Page Image Contents